LG GM210 Скачать руководство пользователя страница 51

Страница: 51 / 165

- 52 -

LGE Internal Use Only

Only for training and service purposes

3. TECHNICAL BRIEF

LGE Internal Use Only

Use of the JackSense Terminal for Accessory Insertion and Removal Detection

Accessory insertion and removal is detected using the JackSense terminal. The JackSense terminal is

connected to a signal produced by a mechanical connection that indicates the presence or absence of

the headset accessory. The insertion/removal sense circuit fed by JackSense is flexible as far as the

characteristics of the mechanical connection are concerned. The mechanical connection will often times

be pulled down in one state and floating in the other. In such cases a 1uA on chip current source is used

to pull JsckSense to VBAT when the mechanical connection is floating.

To avoid false interrupts the Accessory detect logic has a hardware polling loop which will prevent

Interrupt generation from comparator transitions with a duration of no less than 10 mSec.

Figure 3-13-6 Accessory Insertion/Removal Detector Block Diagram

Содержание GM210
































































































































































Результаты поиска

Содержание GM210

Отзывы:

LG GM210, Руководство по обслуживанию, Страница: 51 / 165

Результаты поиска

Содержание GM210

Отзывы: