manualshive.com logo in svg

LG GCE-8160B, Руководство по обслуживанию

Поделиться
Скачать
LG GCE-8160B Скачать руководство пользователя страница 30

42

118

IORDY

TTL Output, SMT,

Slew rate, PDR

I/O Channel Ready.  Ultra DMA ready.  Ultra DMA data strobe.
For I/O channel Ready,  this signal is negated to extend the host
transfer cycle of any register read or write when the device is not
able to complete the transfer.
For Ultra DMA Ready,  this signal is asserted by the device to
indicate to the host that the device is ready to receive Ultra DMA
data out bursts from the host.
For Ultra DMA data strobe, this is the data in strobe signal from
device for Ultra DMA data in burst to the host.

119

DMACK#

TTL Input, SMT,

50K pull-up

DMA Acknowledge. This signal shall be used by the host in
response to DMARQ to acknowledge that it is ready for DMA
transfers.

120

INTRQ

TTL I/O,

Slew rate

Device Interrupt. This signal is used to interrupt the host system.
INTRQ is driven only when this chip is addressed. When not
driven, INTRQ is in a high impedance state.

121

IOCS16#

TTL Output,

Open-Drain

Device 16-BIT I/O.  In PIO transfer modes 0, 1, and 2, IOCS16#
indicates to the host system that the 16-bit data port has been
addressed and that the device is prepared to send or receive a
16-bit data word.

 

124

PDIAG#

TTL I/O,

50K pull-up

Passed Diagnostics. This signal is asserted by Device 1 to
indicate to Device 0 that it has completed diagnostics.

126, 123, 125

HA2, HA0, HA1

TTL Input, SMT,

50K pull-up

Device Address. This is the 3-bit binary coded address provided
by the host to access an ATA register or data.

128

CS1FX#

TTL Input, SMT,

50K pull-up

Device Chip Select 0

  (for 1Fxh/17xh). This is the chip select signal

from the host to select the Command Block Registers.

129

CS3FX#

TTL Input, SMT,

50K pull-up

Device Chip Select 1 (for 3Fxh/37xh). This is the chip select signal
from the host to select the Control Block Registers.

 

 

130

DASP#

TTL I/O,

50K pull-up

Device Active / Device 1 Present. This is a time-multiplexed signal
that indicates

 

that a device is active, or that Device 1 is present.

132

DEVSEL

TTL Input, SMT,

50K pull-up

Device Select. Cleared to zero indicates the driver is master
device. Set to one indicates the driver is slave device.

Buffer Memory Interface

141

BA1

3.3V CMOS

Output,

Slew rate, PDR

SDRAM bank address 1 signal. For SDRAM application only.
When 4-bank SDRAM is used, this pin is used to select bank2 and
bank3 space and musts connect to “BA1” pin of SDRAM.
When two 2-bank SDRAM are used, this pin is used as “Chip
Select” signal output for second SDRAM and musts connect to
“CS#” pin of second SDRAM.

142

BA0

3.3V TTL Output,

Slew rate, PDR

SDRAM bank address 0 signal. For SDRAM application only.

153

DQML

3.3V CMOS

2

Output,

Slew rate, PDR

3

SDRAM low-byte data output mask control signal, high active. For
SDRAM application only.

Содержание GCE-8160B











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды