LG EH048252P3S1 Скачать руководство пользователя | Manualshive

Страница: 30 / 50

background image

30

The RESU Plus has glands and grommets attached to their own places.
The table below lists the number of each item included.

Power cables

2

Anchor bolts

2

5.3 Securing RESU Plus to wall

Secure the RESU Plus to a wall to prevent it from moving.

1. Remove the front cover of the RESU Plus.

Loosen the screws at each corner of the cover

and pull it up.

2. Loosen the screws at each corner of the metal

plate that supports the circuit board. Be careful

not to separate the circuit board from the metal

plate.

RESU Plus Installation

«
...
28
29
30
31
32
...
»

Содержание EH048252P3S1



















































Отзывы:

Нет отзывов

Похожие инструкции для EH048252P3S1

Бренд: Falcon Страницы: 19

Бренд: OEM Tools Страницы: 4

Бренд: Backyard Products Страницы: 72

Бренд: IBM Страницы: 117

Бренд: U-Line Страницы: 39

Cold Frame Single

Бренд: Palram Страницы: 11

EXOS ENTERPRISE ST10000NM001G

Бренд: Seagate Страницы: 56

Бренд: garofalo Страницы: 20

Бренд: Simplay3 Страницы: 2

Бренд: SAJ Страницы: 43

microSDXC UHS-?

Бренд: Toshiba Страницы: 5

SecureAccess SDCZ73-064G-I35

Бренд: SanDisk Страницы: 3

Бренд: SanDisk Страницы: 2

Бренд: Sandberg Страницы: 21

Бренд: Verbatim Страницы: 2

Бренд: Dahua Technology Страницы: 40

Бренд: Xtreamer Страницы: 119

Бренд: QNAP Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды