LG EH048252P3S1 Скачать руководство пользователя | Manualshive

Страница: 40 / 50

background image

40

Commissioning

7.1.2 RESU Plus

There are four LED indicators on the front of the RESU Plus to show its operating status.

ON:

This indicator stays on while the battery pack is supplied with power for operation.

Pack 1:

This stays on while the first battery pack is online with the RESU Plus.

Pack 2:

This stays on while the second battery pack is online with the RESU Plus.

Fault:

This comes on when one or both battery packs are in a warning or fault state.

See

Troubleshooting on page 42

NOTE

At the first commissioning, or when one is additionally installed later, one of the two

battery packs may be inoperative due to the voltage difference between them. The
responsible battery back cannot be online with the RESU Plus until its voltage level
becomes the same as that of the normal one.

7.2 Commissioning battery pack

If only one battery pack is installed, follow these steps to put it in operation.

1. Move the circuit breaker switch to the ON position to turn on the battery pack.
2. Make sure that the ON indicator is on. If it stays off, do not use the battery pack. Contact

LG Chem or your distributor.

3. Turn on the inverter.

«
...
38
39
40
41
42
...
»

Содержание EH048252P3S1



















































Отзывы:

Нет отзывов

Похожие инструкции для EH048252P3S1

Бренд: RAID Страницы: 108

Бренд: Yardmaster Страницы: 23

AP-SRFD255AXXXXR-G

Бренд: Apacer Technology Страницы: 18

Бренд: Y-E Data Страницы: 48

Бренд: Glyph Страницы: 2

Бренд: Spectra Logic Страницы: 15

Бренд: Oracle Страницы: 146

Бренд: SanDisk Страницы: 2

Бренд: HOGYME Страницы: 31

Бренд: NEC Страницы: 69

Бренд: ZRGP Страницы: 33

Бренд: S&C Страницы: 42

Бренд: Clarke Страницы: 2

Бренд: Kelvania Страницы: 12

Бренд: Promise Technology Страницы: 1

Бренд: Newer Technology Страницы: 20

miniStack Classic

Бренд: Newer Technology Страницы: 24

Бренд: TAG Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды