LG EH048252P3S1 Скачать руководство пользователя | Manualshive

Страница: 23 / 50

background image

23

Battery Pack Installation

8. To secure the battery pack to the wall, replace

the top cover and tighten the screws to a torque

of 2.75 N·m.

4.5 Installation clearance

Make sure to leave a space of at least 9 mm between the battery pack and the wall.
A clearance of at least 9 mm must be left around the battery pack for proper cooling.

NOTE

Make sure that the battery pack is always exposed to the ambient air. The battery pack
is cooled by natural convection. If the battery pack is entirely or partially covered or
shielded, it may cause the battery pack to stop operating.

«
...
21
22
23
24
25
...
»

Содержание EH048252P3S1



















































Отзывы:

Нет отзывов

Похожие инструкции для EH048252P3S1

XCubeSAN XS5224D

Бренд: Qsan Technology Страницы: 143

4big Spare Drive

Бренд: LaCie Страницы: 24

Бренд: Glyph Страницы: 2

Бренд: Alphacool Страницы: 2

BARRACUDA ST1000DM014

Бренд: Seagate Страницы: 29

Бренд: Addonics Technologies Страницы: 8

Бренд: Gardener's Страницы: 2

Бренд: Kanguru Страницы: 22

StoreJet 18 mobile

Бренд: Transcend Страницы: 21

Бренд: Transcend Страницы: 19

FileStore N8300

Бренд: Symantec Страницы: 55

Бренд: Pollard Страницы: 3

Бренд: OLT Страницы: 35

G-RAID with Thunderbolt

Бренд: G-Technology Страницы: 52

Бренд: Ensurity Technologies Страницы: 75

Leopold Bench Kit

Бренд: Austin Kontore Страницы: 12

Бренд: Corvus systems Страницы: 291

Бренд: Grizzly Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды