LG CodePlus OAT100R Скачать руководство пользователя страница 3

Страница: 3 / 75

206-4218

1.   Read these instructions.
2.   Keep these instructions.
3.   Heed all warnings.
4.   Follow all instructions.
5.  Do not use this apparatus near water.
6.  Clean only with dry cloth.
7.  Do not block any ventilation openings.

Install in accordance with the manufac-

turer's instructions.

8. Do not install near any heat sources,

such as radiators, heat registers, stoves,

or other apparatus (including amplifiers)

that produce heat.

9. Do not defeat the safety purpose of the

polarized or grounding-type plug. A polar-

ized plug has two blades with one wider

than the other. A grounding-type plug has

two blades and a third grounding prong.

The wide blade or the third prong are

provided for your safety. If the provided

plug does not fit into your outlet, consult

an electrician for replacement of the

obsolete outlet.

10. Protect the power cord from being walked

on or pinched, particularly at plugs,

convenience receptacles, and the point

where it exits from the apparatus.

11. Only use attachments/accessories

specified by the manufacturer.

12. Use only with the cart, stand, tripod,

bracket, or table specified by the

manufacturer or sold with the apparatus.

When a cart is used, use caution when

moving the cart/apparatus combination

in order to avoid injury from tip-over.

13. Refer all servicing to qualified service

personnel. Servicing is required when the

apparatus has been damaged in any way,

such as power-supply cord or plug is

damaged, liquid has been spilled or

objects have fallen into the apparatus, the

apparatus has been exposed to rain or

moisture, does not operate normally, or

has been dropped.

14. Power Sources

This product should be operated only from the

type of power source indicated on the marking

label. If you are not sure of the type of power

supply to your INSTALLATION, consult your

product dealer or local power company.

15. Overloading

Do not overload wall power outlets and

extension cords as this can result in a risk of

fire or electric shock.

16. Disconnect Device

The AC mains plug is used as the disconnect

device. The disconnect device must remain

readily operable.

17. Object and Liquid Entry

Never push objects of any kind into this

product through openings as they may touch

dangerous voltage points or short-out parts

that could result in a fire or electric shock.

Never spill liquid of any kind on the product.

Do not use liquid cleaners or aerosol cleaners.

18. Outdoor Use

Warning: To prevent fire or shock

hazards, do not expose this product

to rain or moisture.

19. Wet Location

Do not use this product near water or mois-

ture or in an area, such as a basement, that

might become flooded.

The apparatus shall

not be exposed to dripping or splashing and

no objects filled with liquids, such as vases,

shall be placed on the apparatus.

20. Test Equipment

In some cases, LG has supplied or recom-

mended the use of test equipment and

devices for the setup and testing of the equip-

ment. The operation and maintenance of test

equipment is described in their associated

instruction manuals. Please refer to these

manuals for explicit instructions regarding the

safe use and handling of the equipment.

(Continued on next page)

IMPORTANT SAFETY INSTRUCTIONS

Содержание CodePlus OAT100R











































































Результаты поиска

Содержание CodePlus OAT100R

Отзывы:

Похожие инструкции для CodePlus OAT100R

Бренды по названию

Популярные бренды

LG CodePlus OAT100R, Инструкция по установке и настройке

Результаты поиска

Содержание CodePlus OAT100R

Отзывы:

Похожие инструкции для CodePlus OAT100R

Бренды по названию

Популярные бренды