LG ARWB100LA2 Скачать руководство пользователя страница 3

Страница: 3 / 86

ENGLISH

Installation Manual 3

Safety Precautions

Safety Precautions

To prevent injury to the user or other people and property damage, the following instructions must
be followed.

■

Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is
classified by the following indications.

■

Meanings of symbols used in this manual are as shown below.

This symbol indicates the possibility of death or serious injury.

This symbol indicates the possibility of injury or damage to properties only.

Be sure not to do.

Be sure to follow the instruction.

■

Installation

Have all electric work done by a licensed
electrician according to "Electric Facility
Engineering Standard" and "Interior Wire
Regulations" and the instructions given in
this manual and always use a special circuit.

• If the power source capacity is inadequate or electric work

is performed improperly, electric shock or fire may result.

Ask the dealer or an authorized technician to
install the air conditioner.

• Improper installation by the user may result in water leak-

age, electric shock, or fire.

Always ground the product.

• There is risk of fire or electric shock.

Always intstall a dedicated circuit and breaker.

• Improper wiring or installation may cause fire or electric

shock.

For re-installation of the installed product,
always contact a dealer or an Authorized
Service Center.

• There is risk of fire, electric shock, explosion, or injury.

Do not install, remove, or re-install the unit
by yourself (customer).

• There is risk of fire, electric shock, explosion, or injury.

Do not store or use flammable gas or
combustibles near the air conditioner.

• There is risk of fire or failure of product.

Use the correctly rated breaker or fuse.

• There is risk of fire or electric shock.

Do not install the unit outdoor.

• Otherwise it may cause fire, electric shock and trouble

Do not install the product on a defective
installation stand.

• It may cause injury, accident, or damage to the product.

Содержание ARWB100LA2























































































Результаты поиска

Содержание ARWB100LA2

Отзывы:

Похожие инструкции для ARWB100LA2

Бренды по названию

Популярные бренды

LG ARWB100LA2, Руководство по установке

Результаты поиска

Содержание ARWB100LA2

Отзывы:

Похожие инструкции для ARWB100LA2

Бренды по названию

Популярные бренды