LG-Ericsson iPECS eMG100 Скачать руководство пользователя страница 335

Страница: 335 / 718

iPECS eMG80/100& eMG800 & UCP & vUCP
Administration and Programming Manual

Issue 2.3

318

Table 4.4.4.1-1 Common Attributes

ATTRIBUTE

DESCRIPTION

RANGE

DEFAULT

Burst Tone to

Caller

When DID Call Wait is assigned for the station, the system can

send audible off-hook signals as a short burst of tone for DID calls

from this CO/IP Line.

OFF

Collect Call

Blocking

This parameter defines the type of Collect Call Blocking supported

for E1 CO lines with R2 signaling. (Intended for Brazil

only)

Disable, Double Answer, Double Answer w/Indication

Refer to

description

Disable

Collect Call

Answer Timer

These parameters determine treatment of an incoming call when

Collect Call Blocking Double Answer is assigned. In this case, the

system answers the call and maintains the connection for the Call

Answer time then, the system will disconnect for the Call Idle time

before finally reconnecting the call.

1-250

(100ms)

Collect Call Idle

Timer

1-250

(100ms)

Gain table index One of three Gain tables can be configured for TDM connections. 1-3

Tone table index

One of the five Tone table can be configured for use with the

CO/IP Line.

1-5

Digit conversion

table index

One of the Digit Conversion Tables can be configured for use for

this CO/IP Line.

1-15(eMG80/100), 1-32(eMG800), 1-32(UCP)

Refer to

description

Prepaid Call

The Pre-paid Call feature must be enabled for use by a station.

User can set the budget for the station call charge in advance.

OFF

Prepaid Money

(0-999999)

Used Prepaid

Money

An amount can be associated with the station as prepayment for
outgoing calls. The assigned “Pre-paid Money” is reduced by the

calculated call cost (Call Metering or cost/minute). This parameter

displays the remaining funds for outgoing calls. Prepaid Money is

often used in small hospitality businesses.
The “Used Pre-paid Money” displays the money that has been

used.

0-999999

Automatic call

recording

destination

When desired, the IP CR server can be used to record calls on

the CO/IP Line. This value defines the Station Group of the IP CR

server. The IP CR Agent object, see PGM 237, must be assigned

as CO Line for proper operation.

ICLID Usage

An incoming call can be routed to the destination based on Calling

Name.



Disable

- ICLID feature is disabled



CLI

- ICLID feature is operated with CLI



Name, CLI

- ICLID feature is operated with Name and CLI

Refer to

description

CLI

PBX Code

Insertion for

Emergency call

System can insert PBX code automatically if pre-configured when

a user make an emergency call.

Disable, PBX code1~4

Refer to

description

Disable

Timer Attributes

Cut Off Timer

When the Station is assigned Call Time restriction is assigned,

this timer defines the allowed call duration.

00-99

00 =

disable

Содержание iPECS eMG100















































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание iPECS eMG100

Отзывы:

Бренды по названию

Популярные бренды

LG-Ericsson iPECS eMG100, Руководство по программированию

Результаты поиска

Содержание iPECS eMG100

Отзывы:

Бренды по названию

Популярные бренды