LG-Ericsson iPECS eMG100 Скачать руководство пользователя страница 328

Страница: 328 / 718

iPECS eMG80/100& eMG800 & UCP & vUCP
Administration and Programming Manual

Issue 2.3

311

Table 4.4.3.1-1 H.323 VOIP ATTRIBUTES

ATTRIBUTE

DESCRIPTION

RANGE

DEFAULT

RAS Uni-cast IP

Address

This parameter defines the Unicast IP address for RAS

Information of Gatekeeper.

IP Address 82.134.80.2

RAS Keep Alive

Time

To maintain a connection, the system and GateKeeper must

exchange RAS Information prior to expiration of this timer.

001-999

(seconds)

120

RAS Number Plan

Prefix

The numbering plan for Calling Number in RAS Setup.

Max. 23

digit

RAS Light RRQ

Usage

The system can be assigned to use the simple RRQ

(Registration Request) message (ON) or the full RRQ

message (OFF).

OFF

RAS Gateway ID

The Gatekeeper ID.

128

characters

Fail Over Usage

If an H.323 call fails to set-up in the

‘Call Setup No Response

time

’ below, the system will attempt to place the call on the

Failover CO/IP group also defined below.

OFF

Call Setup No

Response Time

When Failover is enabled, the system places the fail-over call if

this timer expires before the system receives a response to

setup messages.

0, 3-15

Sec.

Failover CO Group

Number

The system will place the Fail-over call employing a CO/IP line

from the assigned CO/IP Line Group.

eMG80/100:1-21, eMG800:1~201, UCP:1~201

Refer to

description

VOIP(VOIU) GW Port Usage

Q.931 Port Range IP-Binding H.323 signaling option: Q.931 TCP Port Range.

TCP port

2048-2559

H.245 Port

Range IP-Binding H.323 signaling option: H.245 TCP Port

Range.

TCP port

2560-3071

RAS Port Range

IP-Binding H.323 signaling option: RAS UDP Port Range.

UDP port

2048-3071

Media Port Range

IP-Binding media option: Media UDP Port Range.

Default: eMG80/100:6000-7036, eMG800:6000-14400,

UCP:6000-19972

UDP port

Refer to

description

Data Sharing Port

Range

IP-Binding option: Data Sharing TCP Port Range.

TCP port

8500-8548

External CODEC Priority Configuration

External CODEC

Priority

Configuration

The system supports five Codecs and, for negotiating

purposes, the priority of each can be defined. Codecs not

assigned a consecutive priority are not available during

negotiations with the host.

None/

g.711-u/

g.711-a/

g.723.1/

g.729/

g.729a

None

Содержание iPECS eMG100















































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание iPECS eMG100

Отзывы:

Бренды по названию

Популярные бренды

LG-Ericsson iPECS eMG100, Руководство по программированию

Результаты поиска

Содержание iPECS eMG100

Отзывы:

Бренды по названию

Популярные бренды