Levitronix PLD-iF30SU.1 Скачать руководство пользователя страница 28

Страница: 28 / 39

User Manual for PuraLev

iF30SU

www.levitronix.com

PL-4078-00, Rev00, DCO# 20-228

4.3.7 Installation of RS485 Fieldbus for Flow Control Arrays

Figure 25

shows a flow control arrangement with the

RS485

fieldbus and its basic specifications.

Figure 25: Flow control array arrangement with RS485 fieldbus

Following points and information shall be considered:

➔

Testing has been done with arrangements of 8 systems. Higher number is possible but it is recommended to contact

Levitronix

Technical Service

department (see

Section 8

) for details and support.

➔

Address setting of the pump units can be done with the

Levitronix

Service Software

and a

PC. A USB/RS485

converter cable with integrated initialization network can be ordered according to

Table 4

➔

The

RS485

protocol for master communication is available at

Levitronix

on request.

➔

Do not use multiple master systems at the same time.

➔

Do not use closed ring arrangements.

4.4 Electrical Installation of Flow Sensor

1. Every sensor comes delivered with a calibration sheet. Check if the S/N on the calibration sheet corresponds to the

S/N on the type label of the sensor.

2. Please store the delivered calibration sheet or its data on a defined storage place in order to be able to refer to it in

case of problems.

3. Attach one of the sensor extension cables (

Table 4

Position 10a

) coming from the driver to the sensor connector.

4. When applying power, the flow control drivers needs about 10 seconds for a start-up procedure to be ready. In order

to get stable temperature and signals for flow converter and sensor 30 minutes shall be waited after power-on.

5. After start-up a Zero adjustment is recommended as described in

Section 4.8

Integrated Flow

Control Driver

OEM Model

Integrated Flow

Control Driver

OEM Model

Integrated Flow

Control Driver

OEM Model

24 VDC

Supply

IPS Cable Hybrid

Single-Use

Pump Head

Single-Use

Pump Head

Single-Use

Pump Head

Flow
Sensor

120



120



510



510



Master

Main Bus Line: < 100 m

Shielded cable with twisted wires recommended.

Termination:

Recommended for main bus line Length > 5m.

Initialization Network:

Always recommended.
To be implemented at the master.

Branch Bus Lines:

Length sum of all < 33 m

24 VDC

Supply

24 VDC

Supply

RS485+

RS485-

Содержание PLD-iF30SU.1








































Результаты поиска

Содержание PLD-iF30SU.1

Отзывы:

Похожие инструкции для PLD-iF30SU.1

Бренды по названию

Популярные бренды

Levitronix PLD-iF30SU.1, Руководство пользователя

Результаты поиска

Содержание PLD-iF30SU.1

Отзывы:

Похожие инструкции для PLD-iF30SU.1

Бренды по названию

Популярные бренды