manualshive.com logo in svg

Levitronix PLD-iF30SU.1, Руководство пользователя, Страница: 19 / 39

Поделиться
Скачать
Levitronix PLD-iF30SU.1 Скачать руководство пользователя страница 19

 

User Manual for PuraLev

®

 iF30SU 

www.levitronix.com 

 

PL-4078-00, Rev00, DCO# 20-228 

 

19

 

 

4.1.3  Installation Instructions for Power Supply 

 

 

 

! 

 

WARNING

 

 

Hazardous voltage may be present. 

Always  isolate  the  electrical  power  supply  before  making  or  changing 
connections to the unit.  

In  case  of  the  usage  of  an  inadequate  AC/DC  power  supply,  mains 
voltages may be present (even if the system is designed for  24 VDC). 
The usage of a galvanic separated power supply, which is certified by a 
3

rd

 party (UL or CE), is highly recommended. 

 

1. 

A certified and tested desktop power supply with a specific connector is available as an accessory 
(see 

Table 4

), which allows simple direct connection to the driver. 

2. 

For  other  power  supplies  an  open  wire  power  cable  for  connection  to the  driver  is  specified  in 

Table 4

 (cable type 

ICP-1.1

). Depending on the required hydraulic operational point (see 

Figure 

8

),  the  flow  control  system  requires  24  VDC  with  a  maximum  power  of  35  W.  At  a  lower 

performance power supplies with smaller power or bigger supplies to power several flow control 
systems simultaneously may be used.

 

Consult 

Figure 16

 to get the power consumption depending 

on  the  flow.

 

If  power  supplies  are  used  other  than  the  one  defined  by 

Levitronix

®

,  it  is  highly 

recommended to test these under dynamic conditions (acceleration and braking of the pump rotor 
speed). 

3. 

Make sure that the polarity is correct, and that AC/DC power supply is off. 

 

4.1.4  Installation of Flow Sensor 

See 

Section 4.4

. 

 

4.1.5  Installation PLC Interface Signals 

To operate the  flow control system with a 

PLC

 the analog input can  be  used to  set  the  flow or speed. The 

digital output can be used to monitor the pump status and operating parameters (see

 

Table 10

). 

 

 

CAUTION

 

 

The analog input is not galvanically isolated from the controller 
electronics.  To  avoid  ground  loops  and  malfunctions,  use 
floating analog signals.

 

 

1. 

Power off the system. 

2. 

A signal cable with driver connector is available to simplify PLC  wire connections (see 

Table 4

 

cable type 

ICS-1.3

). Connect the designated PLC wires according to

 

Table 10.

 

3. 

Follow

 

Figure 20

 

as reference for hardware configuration of the PLC inputs and outputs. 

4. 

Protect the un-used wires against short-circuit to each other 

 

Содержание PLD-iF30SU.1








































Отзывы:

Нет отзывов