Leviton DLR Скачать руководство пользователя страница 43

Страница: 43 / 63

User Guide

Page 42

3. idle drop to 0

d= drop to 0
k= keep last level indefinitely

Determines what happens when a DMX which was

transmitting data suddenly disappears. The cause for

this could be power failure (at the source, cable

interruption, etc.).

A drop to setting says that upon loss of signal, the

output will immediately stop outputting DMX.

A keep setting tells the NPC to keep the last level

received indefinitely until new instructions are received.

4. DMX Level Precedence

H= highest level takes precedence
L= last action takes precedence

Determines the plan of action when two patched DMX

Channel Levels are different yet patched to the same

output. If level precedence is set to highest, the

highest level will be the output level at all times. This

option is usually considered a straight merge. If level

precedence is set to last, the last action by any input

determines the output level. Last action precedence is

also referenced as "take control".

5. DMX/Luma-Net Merge Procedure

H= highest level takes precedence
L= last action takes precedence

Determines the precedence between all DMX levels

and the Luma-Net inputs.

For example:

Channel Options as set in the above figure 17 will have

the following result: DMX Output port 1 for all 512

channels will immediately drop to 0) upon loss of

signal. All patched DMX source channels and all

patched Luma-Net source channels will be merged in a

highest channel takes precedence mode.

DMX Output port 2, for all 512 channel, will keep levels

upon loss of signal. All patched DMX source channels

will be merged together in a highest takes precedence

mode, however, Luma-Net will be combined with the

Содержание DLR
































































Результаты поиска

Содержание DLR

Отзывы:

Бренды по названию

Популярные бренды

Leviton DLR, Руководство пользователя

Результаты поиска

Содержание DLR

Отзывы:

Бренды по названию

Популярные бренды