Lenze L-force Communication ModemCAN EMF2181IB Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 83

Lenze L-force Communication ModemCAN EMF2181IB Скачать руководство пользователя страница 9

Safety instructions

Device− and application−specific safety instructions

l

9

EDSMF2181IB EN 3.0

2.2

Device− and application−specific safety instructions

ƒ

During operation, the communication module must be securely connected to the
standard device.

ƒ

With external voltage supply, always use a separate power supply unit, safely
separated in accordance with EN 61800−5−1 in every control cabinet (SELV/PELV).

ƒ

Only use cables that meet the given specifications. (

¶

,

Documentation of the standard device, control system, and plant/machine

All the other measures prescribed in this documentation must also be
implemented. Observe the safety instructions and application notes contained
in this manual.

2.3

Residual hazards

Protection of persons

ƒ

If inverters are connected to phase−earthed system with a rated mains voltage

³

400 V, external measures need to be implemented to provide reliable protection

against accidental contact. (see chapter "4.2",

^

Device protection

ƒ

The communication module contains electronic components that can be damaged
or destroyed by electrostatic discharge.

«
...
7
8
9
10
11
...
»

Содержание L-force Communication ModemCAN EMF2181IB




















































































Отзывы:

Нет отзывов