manualshive.com logo in svg

Lenze L-force Communication ModemCAN EMF2181IB, Руководство по связи, Страница: 32 / 83

Поделиться
Скачать
Lenze L-force Communication ModemCAN EMF2181IB Скачать руководство пользователя страница 32

Commissioning

Commissioning with the system bus configurator

6

     

l

 32

EDSMF2181IB  EN  3.0

6.2

Commissioning with the system bus configurator

)

Note!

A window−compatible modem must be installed in the windows system
control.
The communication is executed via the TAPI interface.

System requirements

The following minimum requirements of hardware and software must be met to work
with the communication module:

ƒ

Microsoft

R

 Windows

R

 2000/XP

ƒ

IBM

R

−compatible PC with Intel

R

Pentium

R

−266 processor or higher

ƒ

128 MB main memory with Windows2000/XP

Available Lenze programs

The following Lenze programs allow for a communication via the communication module
:

ƒ

Drive Server

ƒ

Global Drive Control (GDC version 4.7 or higher)

ƒ

Global Drive Loader

ƒ

Global Drive PLC Developer Studio (DDS version 1.4 or higher)

ƒ

L−force Engineer

)

Note!

One of the programs mentioned offer alternative communication paths for
CAN. In this case, please always select the communication path "OPC".

Содержание L-force Communication ModemCAN EMF2181IB




















































































Отзывы:

Нет отзывов