Lenze E84DGFCA Series Скачать руководство пользователя страница 38

Страница: 38 / 75

Data transfer

Data transmission slave 2 (AS-i profile 7.A.7)

Lenze · Decentralised frequency inverter 8400 motec (AS-Interface option) · EDS84DMOTASI EN 5.0 - 02/2019

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

Accessing the parameter bits

Parameter bits P0 ... P3 provide diagnostic information to the master for slave 2. Here, P0 ... P2

define whether a status query of code

C00150

or an error/warning diagnostics is returned as slave

response to the master.
The values of P0 ... P3 are transmitted to the master via the "Write_Parameter" command.

Error messages and warnings

Bits

Signal / I/O mapping

Description

Diagnostic information

(slave



master):

• 4 status bits of the status word

C00150

• Error messages / warnings (see

below)

Values P0 - P1 - P2:

• 0 - 0 - 0: Query C00150/Bits 0 ... 3

• 0 - 0 - 1: Query C00150/Bits 4 ... 7

• 0 - 1 - 0: Query C00150/Bits 8 ... 11

• 0 - 1 - 1: Query C00150/Bits 12 ... 15

• 1 - 0 - 0: Active error

• 1 - 0 - 1: Active warning

P1
P2
P3



Note!

No error message / warning is ever provided other than the one with the highest priority.

As long as this error message / warning is pending, no other can be provided.

Values

Error message

Warning

No failure

No warning

"OC1" - Short circuit

"OC5" - Device load warning

"OC2" - Ground fault

"OC6" - Overload warning

"OH" - High temperature

Heat sink temperature high warning

"US02" - User error #1

"US01" - User warning #1

"OU" - High bus voltage

Brake resistor overload

"LU" - Low bus voltage error

"LU" - Low bus voltage warning

"OC6" - Overload error

Motor identification active

"Su02" - Single phasing

"US02" - User error #2

"US02" - User warning #2

"dbF" - Dynamic brake fault

AutoStartLock

"PS0x" - EPM failure

Motor phase failure

"DF0x" - Internal failure

AIN current < 4 mA

"OH3" - PTC fault

Reserved (unused)

Drive Unit "offline"

Reserved (unused)

Other failure

Other warnings

Содержание E84DGFCA Series












































































Результаты поиска

Содержание E84DGFCA Series

Отзывы:

Похожие инструкции для E84DGFCA Series

Бренды по названию

Популярные бренды

Lenze E84DGFCA Series, Руководство по связи

Результаты поиска

Содержание E84DGFCA Series

Отзывы:

Похожие инструкции для E84DGFCA Series

Бренды по названию

Популярные бренды