background image

This documentation applies to the use of an MCH Series Variable Frequency Drive with BACnet protocol and should 
be used in conjunction with the MCH Series Installation and Operation Manual (Document MH01) that shipped with 
the drive. These documents should be read in their entirety as they contain important technical data and describe 
the installation and operation of the drive.

ASHRAE  and  BACnet®  are  registered  trademarks  of  the  American  Society  of  Heating,  Refrigerating  and  Air-
Conditioning Engineers, Inc., 1791 Tullie Circle NE, Atlanta, GA 30329, http://www.bacnet.org.

Modbus ™ is a registered trademark of Schneider Electric, founder of Modbus-IDA, http://www.modbus-IDA.org.

©  2003 AC Technology Corporation
No part of this documentation may be copied or made available to third parties without the explicit written approval 
of AC Technology Corporation. All information given in this documentation has been carefully selected and tested 
for compliance with the hardware and software described. Nevertheless, discrepancies cannot be ruled out. AC 
Tech does not accept any responsibility nor liability for damages that may occur. Any necessary corrections will be 
implemented in subsequent editions.

About These Instructions

Содержание AC Tech MCH Series


















Отзывы: