Lenze AC Tech LonWorks MCH Series Скачать руководство пользователя страница 7

Страница: 7 / 27

RG-MHLON

Drive Setup & Programming

2.2 LED Status Indicators

LED 1 - Drive Communication

This LED indicates the communication status between the comm module and the drive.

LED State

Indicates:

Steady Green

Link OK

Steady Red

Link lost, permanent

Flashing Red

Link lost, temporary

LED 2 - Service

This LED indicates the node configuration and application status.

LED State

Indicates:

Steady OFF

Node configured and installed in network

Steady Green

Node not configured, has no application; Error detected by Neuron Self Test routine

Flashing Green Node not configured and not installed in network but node has an application

LED 3 - Wink

This LED indicates receipt of a wink command.

LED State

Indicates:

Flashing Red

Wink command received on LonWorks

network

Steady OFF

Normal state

LED 4 - Network Status

This LED indicates the communication status between the module and the LonWorks® network.

LED State

Indicates:

Steady OFF

No power

Flashing Red

Receive heartbeat timeout occurred; Fieldbus communication loss indicated to host: RX_FAIL

Steady Green

Module and network are communicating correctly

Watchdog LED (WD)

This LED indicates module, drive and software status.

LED State

Indicates:

Flashing Green 1Hz Module initialized and running properly
Flashing Green 2Hz Module not initialized
Flashing Red 1Hz

Hardware check fault

Flashing Red 4Hz

Drive initialization failed

Steady Orange

Software download enabled

Содержание LonWorks MCH Series




























Результаты поиска

Содержание LonWorks MCH Series

Отзывы:

Бренды по названию

Популярные бренды

Lenze AC Tech LonWorks MCH Series, Руководство по связи

Результаты поиска

Содержание LonWorks MCH Series

Отзывы:

Бренды по названию

Популярные бренды