manualshive.com logo in svg

Lenze AC Tech LonWorks MCH Series, Руководство по связи

Поделиться
Скачать
Lenze AC Tech LonWorks MCH Series Скачать руководство пользователя страница 20

 

17 

RG-MHLON

LonWorks Network Variables

NvoFreqAct

Definition 

Network output SNVT_freq_hz nvoFreqAct

Explanation 

This output network variable provides the speed of the drive in Hz.

Valid Range 

0.0 - 120.00 Hz

Default Value  0.00 Hz

NvoDrvStatus

Definition 

Network output SNVT_state nvoDrvStatus

Explanation 

This output network variable provides the status of the drive.

Valid Range 

Bit

Name

Description

0

FWD

The drive is currently running the motor in forward motion

1

REV

The drive is currently running the motor in reverse motion

2

NETCTRL

The network is the active source for start/stop control

3

NETREF

The network is the active source for the speed reference

4

RTSO

Not used

5

FAULT

The drive is currently faulted

6

ALARM

Not used

7

REF

The drive is running the motor at the speed defined by the 
speed reference of the active control source (i.e. actual drive 
speed = commanded drive speed)

8

FORN

Not used

9

ZERO SPEED The drive is running at zero speed

10

LIMIT

Not used

11

ACC

The drive is currently ramping up to its commanded speed

12

DEC

The drive is currently ramping down to its commanded speed

13-15 Not used

Not used

Default Value  0

Содержание LonWorks MCH Series




























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды