manualshive.com logo in svg

Lenze AC Tech LonWorks MCH Series, Руководство по связи

Поделиться
Скачать
Lenze AC Tech LonWorks MCH Series Скачать руководство пользователя страница 26

 

23 

RG-MHLON

LonWorks Network Variables

nciParWrite

Definition 

Network config input SNVT_count nciParWrite

Explanation 

Chooses the parameter value to be written to the drive.

Valid Range 

1 - 46

Default Value  0

4.5  LonWorks XIF Files

The LonMark external interface (or XIF) file is used to set up a LonWorks network with an MCH Series drive 
that has not yet been commissioned. These files are available for download in the Technical Library of the 
Lenze-AC Tech website.

Use Drive Parameter #63 to retrieve the software version of your MCH drive. Drives with software versions 
MC11103 and later, and MC121xx use the 21312203.XIF file. If your MCH drive has an earlier software 
version (MC11101 or MC11102), then contact technical support for the appropriate XIF file.

4.6  Reference and Links

MCH Series Variable Frequency Drives visit:

http://www.lenze-actech.com

LonWorks and Echelon Corporation visit:

http://www.echelon.com

LonMark Functional Profiles (including 6010) visit:

http://www.lonmark.org

ANYBUS-S Drive Profile Embedded Interface Cards, LonMark 6010 Functional Profile visit:

http://www.anybus.com/products/abs.shtml

Содержание LonWorks MCH Series




























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды