manualshive.com logo in svg

Lenze AC Tech LonWorks MCH Series, Руководство по связи

Поделиться
Скачать
Lenze AC Tech LonWorks MCH Series Скачать руководство пользователя страница 19

RG-MHLON 

16

LonWorks Network Variables

NvoDrvCurnt

NOTE:

 This parameter is not supported in drives with software version MC11101 or MC11102.

Definition 

Network output SNVT_amp nvoDrvCurnt

Explanation 

This output network variable provides the drive output current in Amps.

Valid Range 

0.0 to 3276.7 A

Default Value  0.0 A

NvoDrvRunHours

NOTE:

 This parameter is not supported in drives with software version MC11101 or MC11102.

Definition 

Network output SNVT_time_hour nvoDrvRunHours

Explanation 

This output network variable provides total operation time of the motor in hours.

Valid Range 

0 to 65535 hours

Default Value  0 hours

NvoDrvVolt

NOTE:

 This parameter is not supported in drives with software version MC11101 or MC11102.

Definition 

Network output SNVT_volt nvoDrvVolt

Explanation 

This output network variable provides the drive output voltage in Volts.

Valid Range 

0 – 700 V

Default Value  0 V

NvoSpeedActRpm

Definition 

Network output SNVT_count_inc nvoSpeedActRpm

Explanation 

This output network variable provides the speed of the drive in RPM’s

Valid Range 

-32768 to 0 or 0 to 32767

Default Value  0 RPM

Содержание LonWorks MCH Series




























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды