Lenovo ThinkPad 600 Скачать руководство пользователя

Страница: 28 / 221

Attention

You should take corrective actions when the battery status
indicator is

blinking orange, and your computer sounds three

consecutive beeps. (If your computer enters suspend mode
because of a low-battery condition, data in memory might be
lost.)

Immediately connect the AC Adapter to the computer.

Then take either of the following actions:

To continue your work with AC Adapter, press the Fn key.

or:

To continue your work with a fully charged battery pack, do

the following:

1. Replace the battery pack with a fully charged one. (See

the

User's Reference.)

2. Press the Fn key.

3. Disconnect the AC Adapter from the computer.

If you do not take corrective actions within about 30 seconds, the
computer will enter suspend mode.

Do not leave the computer in this condition for an extended
time. Data in memory will be lost.

IBM ThinkPad 600 Online Book

Содержание ThinkPad 600






























































































































































































































Результаты поиска

Содержание ThinkPad 600

Отзывы:

Похожие инструкции для ThinkPad 600

Бренды по названию

Популярные бренды

Lenovo ThinkPad 600, Руководство пользователя

Результаты поиска

Содержание ThinkPad 600

Отзывы:

Похожие инструкции для ThinkPad 600

Бренды по названию

Популярные бренды