Lenovo ThinkPad 600 Скачать руководство пользователя

Страница: 167 / 221

Restart your computer to make the new settings effective.

Installing the IDE Driver for Windows NT

Install the ThinkPad PIIX4 IDE driver as follows:

Start Windows NT and log on with the user ID authorized as an

administrator.

Insert the IDE Driver Diskette into the diskette drive.

Click on Start.

Click on Settings and Control Panel.

Double-click on SCSI Adapters.

Click on the Drivers tab.

If Intel PIIX PCI Bus Master IDE Controller is listed, remove
it.

If IDE CD-ROM (Atapi 1.2)/Dual Channel PCI IDE is listed,
remove it.

Click on Add.

Click on Have Disk...

Click on OK after confirming that the installation path is correct
(usually it points to

A:\

Select ThinkPad PIIX4 IDE Driver; then click on OK.

If you are prompted to restart your computer, remove the
diskette from the diskette drive and click on Yes.

Chapter 8. Installing Software

161

Содержание ThinkPad 600






























































































































































































































Результаты поиска

Содержание ThinkPad 600

Отзывы:

Похожие инструкции для ThinkPad 600

Бренды по названию

Популярные бренды

Lenovo ThinkPad 600, Руководство пользователя

Результаты поиска

Содержание ThinkPad 600

Отзывы:

Похожие инструкции для ThinkPad 600

Бренды по названию

Популярные бренды