Lenovo IdeaPad S200 Скачать руководство пользователя

Страница: 97 / 138

9. Align the tab

on the right side of the front audio and USB assembly bracket with the right side of the

corresponding slot in the chassis. Then pivot the front audio and USB assembly bracket inwards until it
snaps into position on the left side.

Figure 23. Installing the front audio and USB assembly bracket

10. Install the screw to secure the front audio and USB assembly bracket to the chassis.

11. Reconnect the front audio and USB assembly cables to the front audio connector and the front USB

connector on the system board. See “Parts on the system board” on page 34.

12. Install the front bezel. See “Replacing the front bezel” on page 83.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 109.

Replacing the card reader

Attention:

Do not open your computer or attempt any repair before reading and understanding the Chapter

1 “Read this first: Important safety information” on page 1.

To replace the computer handle, do the following:

1. Remove any media from the drives and turn off all connected devices and the computer. Then,

disconnect all power cords from electrical outlets and disconnect all cables that are connected to the
computer.

2. Remove the computer cover. See “Removing the computer cover” on page 82.

3. Remove the front bezel. See “Replacing the front bezel” on page 83.

4. Locate the card reader. See “Computer components” on page 31.

5. Disconnect the card reader cable from the system board.

Note:

Ensure that you note the location of the cable when you disconnect the cable from the system

board.

Chapter 9

Installing or replacing hardware

Содержание IdeaPad S200











































































































































Результаты поиска

Содержание IdeaPad S200

Отзывы:

Похожие инструкции для IdeaPad S200

Бренды по названию

Популярные бренды

Lenovo IdeaPad S200, Руководство по техническому обслуживанию аппаратной части

Результаты поиска

Содержание IdeaPad S200

Отзывы:

Похожие инструкции для IdeaPad S200

Бренды по названию

Популярные бренды