Lenovo 70LU Скачать руководство пользователя страница 68

Страница: 68 / 142

Figure 34. Connecting cables to the drive

Cable

From the system board

To the drive

1-to-3 power cable

4-pin power connector

Power connector on the drive

Signal cable

SATA connector 1

Signal connector on the drive

Note:

The 1-to-3 power cable provides three SATA power connectors

, and

. You can connect

any one of the SATA connectors to the drive.

Storage drive in drive bay 3

Drive bay 3 of your server supports only a 2.5-inch hard disk drive or solid-state drive. For information about
drive bays and installation rules, see “Internal drives” on page 44.

• “Removing a storage drive from drive bay 3” on page 56

• “Installing a storage drive into drive bay 3” on page 57

Removing a storage drive from drive bay 3

To remove a storage drive from drive bay 3, do the following:

1. Prepare your server. See “Preparing your server and removing the server cover” on page 41.

2. Remove the front bezel. See “Front bezel” on page 42.

3. Disconnect the signal cable and power cable from the drive.

4. Press the release tab

and slide the drive out of the drive bay.

ThinkServer TS150 User Guide and Hardware Maintenance Manual

Содержание 70LU















































































































































Результаты поиска

Содержание 70LU

Отзывы:

Бренды по названию

Популярные бренды

Lenovo 70LU, Руководство пользователя и руководство по техническому обслуживанию аппаратного обеспечения

Результаты поиска

Содержание 70LU

Отзывы:

Бренды по названию

Популярные бренды