Lenovo 70LU Скачать руководство пользователя страница 97

Страница: 97 / 142

Figure 81. Installing the intrusion switch

4. Connect the intrusion switch cable to the intrusion switch connector on the system board. See “System

board components” on page 19.

Power supply assembly

Your server supports one of the following power supply configurations:

• 250-watt non-hot-swap power supply (80 PLUS Bronze)

• 400-watt non-hot-swap power supply (80 PLUS Platinum)

Note:

To support a discrete graphic adapter, you must select the 400-watt non-hot-swap power supply.

• “Removing the power supply assembly” on page 86

• “Installing the power supply assembly” on page 86

Although there are no moving parts in your server after the power cord has been disconnected, the following
warnings are required for your safety and proper Underwriters Laboratories (UL) certification.

DANGER

Hazardous moving parts. Keep fingers and other body parts away.

CAUTION:
Never remove the cover on a power supply or any part that has the following label attached.

Chapter 5

Replacing hardware

Содержание 70LU















































































































































Результаты поиска

Содержание 70LU

Отзывы:

Бренды по названию

Популярные бренды

Lenovo 70LU, Руководство пользователя и руководство по техническому обслуживанию аппаратного обеспечения

Результаты поиска

Содержание 70LU

Отзывы:

Бренды по названию

Популярные бренды