Lennox Scandium-LP Скачать руководство пользователя страница 7

Страница: 7 / 20

After having selected the final mounting position of the appliance, taking

into account the site requirements as specified in Section 8 of these instruc-

tions, the integrity of the wall, and the feasibility of the proposed supply

pipe routing, the firebox of appliance may be secured to the wall.

To ensure customer safety, be sure to design the installation so that the

strength of both the wall and any wall fixings used are sufficient. Lennox

Hearth Products assumes no responsibility for injuries and damages that

may occur due to improper installation or handling.

The appliance should not be installed until all dry wall sanding and wall

painting has been completed.

11.0 MOUNTING THE APPLIANCE

Non-concealed gas connections may be made using the entry points

on the base of the firebox. A concealed gas connection may be made

using the knockout hole in the center back of the firebox. Select the most

appropriate entry point and knock out the relevant hole.

If a concealed gas connection is to be made, the supply pipe should always

be sleeved through walls and floors using the shortest possible route.

For concealed supply pipe routing, pipes must (where possible) be ver-

tical and providing there is sufficient wall thickness available, they should

be placed in pipe chases. Horizontal pipe runs should be avoided where

possible. Prior to chasing a solid wall, an inspection should be made

to note the proximity of any cables/sockets outlets which may already

be buried. Pipes must be secured using suitable clips and protected

against corrosion. Ideally factory finished protected pipe-work and fittings

should be used. Joints should be kept to a minimum and compression

fittings must not be used. The pipe-work installation must be tested for

soundness before any protection is applied and/or the pipe-work and

fittings are buried.

WARNING

The wall where the appliance is to be installed must

be capable of long-term support of the total load of

the appliance. Measures should also be taken to

ensure sufficient strength to withstand the force of

earthquakes, vibration and other external forces.

Incorrect installation can cause the appliance to fall from the wall and

cause injury. Do not block the ventilation holes of the appliance. The

wall onto which the appliance is installed must be flat. Install only on a

vertical surface. Avoid sloped surfaces.

Installation onto anything other

than a vertical wall may result in fire, damage or injury.

A full size fitting template is supplied to assist with wall mounting.

Mark the positions shown as “Fixing Points” on the wall. If the appli-

ance is to be mounted on the inner leaf of a conventional cavity wall,

or a solid wall, drill four holes using a 5/16" masonry bit, to a depth of

1-11/16". Insert the wall plugs provided.

If the appliance is to be mounted on a dry lined wall or a timber framed

construction wall then special cavity screw fixings will be required which

are not supplied with this product. These should be constructed from

metal and not plastic.

If a concealed gas connection is to be made ensure the gas supply pipe

is in it’s final position and can enter the appliance in the correct position

when the appliance is hung on the wall.

Figure 2 - Wall Fixing Template

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE

™

WARNING

CLEARANCES FROM COMBUSTIBLE MATERIALS

F860041/A

The following clearances must be maintained at all times.
Failure to do so may result in the risk of a fire.
For full information refer to the instruction manual
provided with the heater.

Note : Zero clearance from bottom of heater frame
required for hard combustible floors. Minimum 4”
clearance required to rugs or any fabric floor
coverings. REFER TO INSTRUCTION MANUAL

IMPORTANT : Fabrics, curtains and drapes are not
permited above the heater at any distance and within
20” of the heater sides. No combustible shelves of any
size are permitted above the heater.

Clearance to
combustible
sidewalls 4”
(both sides)

Clearance to combustible ceiling
32” measured from top of appliance
glass panel

Clearance in
front of
heater 20”

F860041/A

Deben mantenerse en todo momento los siguientes espacios
libres. El no hacerlo puede causar un riesgo de incendio.
Consulte el manual de instrucciones suministrado con este
aparato para obtener información completa.

Nota: No se requiere espacio libre desde el borde inferior del
marco del calentador en caso de pisos combustibles duros.
Se requiere un espacio mínimo de 4” entre el calentador y
cualquier alfombra, moqueta o revestimiento de suelo de
tela. CONSULTE EL MANUAL DE INSTRUCCIONES.

IMPORTANTE: No se permite la colocación de telas, cortinas y

similares por encima del calentador a cualquier distancia, ni a

una distancia de 20” de los laterales del calentador. No se

permiten estantes combustibles de cualquier tamaño por

encima del calentador.

Espacio hasta
paredeslaterales
combustibles
4” (ambos lados)

El espacio de 32” hasta un techo
combustible se mide desde el borde
superior del panel de vidrio del aparato

Espacio libre
delante del
calentador 20”

ADVERTENCIA

ESPACIO LIBRE HASTA MATERIALES COMBUSTIBLES

FIREBO

X OUTLINE