Lennox Scandium-LP Скачать руководство пользователя страница 10

10

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE

16.0 SPARK GAP

17.0 ASSEMBLY OF THE GLASS FACIA

Figure 9 - Proper Spark Gap

1/8" to 3/16" Spark Gap

Figure 10 - Key Hole Slots on Glass Facia

1.  Remove the glass panel from all packaging and lay face down on a soft 

surface. Identify the top and bottom of the glass facia by observing 

the orientation of the keyhole shaped slots in the facia fixing brackets 

as shown in Figure 10.

2.  Slide on the side pieces ensuring that the grill fixing holes (shown) are 

aligned towards the top of the glass facia (as shown in Figure 11

).

Grill fixing holes

Figure 11 - Slide on Side Pieces

3. Ensure the sides are neatly aligned with the glass and secure the sides 

using two M6 screws for each side as shown in Figure 12. Do not 

overtighten the screws.

IMPORTANT NOTES: 

•  The screws that are used to attach the brackets to the facia as seen 

in 

Figures 12 and 14

 below MUST NOT be over-tightened.  Over-

tightening of the mounting screws may cause the glass facia to 

slip from its brackets.  The screws should be finger-tightened until 

all side and top frame pieces are assembled and aligned.  At that 

point, tighten the screws in 1/4 turn increments until frame pieces 

are firmly positioned and do not move.

•  If you find that your glass facia is experiencing slippage because of 

this over-tightening of the screws, you can use normal RTV sealant 

to secure the glass facia to its bracket.  Remove the facia from the 

fireplace, apply the sealant to the area where the slippage is oc-

curring, and allow the facia to dry face down until the sealant has 

dried according to the directions on the sealant packaging.

4. Position the grill within the two side pieces ensuring a proper fit.

Figure 12 - Secure Side Pieces

TOP

Side Piece

The gap between the spark electrode and the pilot should be 1/8” to 

3/16” to produce a good spark.  There should be no need to adjust this 

(DO NOT ATTEMPT TO ADJUST THE GAP). If under any circumstances 

the piezo electric spark fails, the pilot cannot be lit manually.

Adjustment to the 

pilot is Not allowed

Finger-tighten all screws until side 

and top frame pieces are in place 

and aligned.  At that point, tighten in 

1/4 turn increments until frame 

pieces are secure.  DO NOT 

OVER-TIGHTEN.

Содержание Scandium-LP





















Отзывы: