Lennox Scandium-LP Скачать руководство пользователя страница 8

8

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE

Insert  the  wall  mounting  screws  into  the  top  wall  plugs,  taking  care 

to leave the screws protruding approximately 3/8” from the wall. Now 

hang the appliance onto these screws through the two keyhole shaped 

holes in the back panel of the appliance. 

Insert the lower mounting screws into the lower wall plugs through the 

corresponding depressed holes in the lower part of the back panel. Do 

not tighten fully.

Before  tightening  the  wall  mounting  screws  fully,  at  this  stage  it  is 

recommended to check the horizontal alignment of the appliance with a 

bubble level, as small adjustments can still be made if necessary. When 

this has been checked, tighten all four fixing screws fully.

To  access  the  upper  fixing  screws  insert  a  screwdriver  through  the 

holes in the deflector plates above the catalyst as shown in Figure 3.

1.0 CHECKING THE BURNER

There  are  no  imitation  fuel  bed  components,  such  as  logs  or  rocks, 

to install. The appliance features a ribbon burner which is designed to 

produce a continuous band of flame over its length. The burner should 

be visually inspected to ensure it is free from any foreign matter. If it is 

necessary to clean or dust off the burner then the glass door should be 

removed by removal of the four retaining screws. Re-fit the glass door 

after cleaning or inspection, ensuring a good seal.

13.0 CONNECTING A GAS LINE

11.0 MOUNTING THE APPLIANCE - continued

Figure 3

A qualified gas appliance installer must connect the gas room heater to 

the gas supply. Consult all local codes. 

The installer must provide an ANSI approved manual shut off valve, flex 

connector and 3/8" NPT fitting.  A flex gas line kit with shut-off valve is 

available (see Page 16 or ordering information).

Route  gas  line  using  techniques  and  materials  prescribed  by  local 

and/or national codes. Only use pipe of 1/2" or greater size to allow full 

gas volume to the gas fireplace. Undue pressure loss will occur if the 

pipe is too small. 

An external regulator must be used on all propane (L.P.G.) heaters, in 

addition to the regulator fitted to the heater, to reduce the supply tank 

pressure to 13" w.c. (maximum).

Regulator

Manual 

Shut-Off

Valve

Union

Sediment

Trap

Fireplace or

Firebox Wall

Wall

Shut-Off

Key

Fireplace or

Firebox Wall

Down

3"

Figure 4

An ANSI approved manual shut-off valve and union must be installed 

upstream  of  the  heater  within  the  fireplace  cavity  when  rigid  pipe  is 

used. Ensure that a sediment trap is installed upstream of the heater 

(

Figure  4

)

  within  the  structure’s  piping  system  to  prevent  moisture 

and contaminants from passing through the pipe to the heater controls 

and burner. Failure to do so could prevent the heater from operating 

reliably.

The  heater  gas  inlet  connection  is  3/8”  NPT  at  the  regulator,  located 

below the burner, in the right hand side of the heater. When tightening 

up the joint to the regulator hold the regulator securely with a wrench 

to prevent the regulator from moving.

      IMPORTANT 

Hold heater regulator with a wrench to prevent 

movement when connecting to inlet piping.

      WARNING 

Connecting directly to a unregulated propane tank 

may cause an explosion.

NOTE:

  See 

Page 19 

for gas line entry point dimensions.

Содержание Scandium-LP





















Отзывы: