Lennox Hearth Products Traditions T300P Series Скачать руководство пользователя | Manualshive

Страница: 22 / 40

background image

ROUTINE MAINTENANCE

* Inspect your stove or insert at minimum frequency stated until you establish a minimum frequency required for
your installation (frequency will vary depending upon fuel BTU value / ash content, usage, and misc. installation
variables).

Page 22

ROUTINE CLEANING

Note: Stove will need to be shut off and cooled enough to
handle before routine cleaning is performed.
Always disconnect power before doing any routine clean-
ing.

The following areas need to be inspected and cleaned
during routine cleaning:

•

UltraGrate



(burn grate)

•

Ash Slide Plate

•

Ash Pan

•

Heat Exchange Tubes

•

Photoeye

•

Exhaust Passages and Vent Pipe

•

Gaskets

•

Window Wash

•

Rear Stove Compartment

UltraGrate



(BURN GRATE)

The UltraGrate



should be inspected periodically to as-

sure that the air holes have not become clogged with ash
or clinkers. The UltraGrate



can easily be cleaned with

the grate scraper / ash pan tool, or it can be removed for
cleaning. It is very important to monitor the ash build up
under the UltraGrate



, as excessive amounts of ash will

block combustion air from entering the grate, causing
pellets to pile-up in the grate. The ash build-up under the
grate is easily dumped into the ash pan by pulling out the
ash slide weekly as shown below. The grate cleaning
procedure is the same for all models.

UltraGrate



* (Recommended Frequency of 1 day – 2 weeks)

ASH PAN

The ash pan will have to be emptied periodically, de-
pending on amount of fuel consumed. The T300P Series
ash pan is pulled straight out using the black pull knob
located on the front of the ash pan (see following pic-
ture).

Ash Pan

* (Recommended Frequency of 2 days – 2 weeks)

ASH SLIDE PLATE

Ash that accumulates around the grate can be “dropped”

into the ash pan without opening the firebox door. Simply

pull open the ash release slide plate as shown in photo

using the grate scraper tool provided. Remove the ash

pan as shown. Note: Make sure to fully close the plates

when finished. Failure to close the ash release slide

plates completely may cause the fuel to burn poorly (due

to reduced airflow through the grate), which may then

cause pellets to “pile up” in the grate.

Ash Slide Plate

*(Recommended Frequency of 1 day – 2 weeks.)

«
...
20
21
22
23
24
...
»

Содержание Traditions T300P Series









































Отзывы:

Нет отзывов

Похожие инструкции для Traditions T300P Series

Бренд: Zero Страницы: 17

Бренд: Drolet Страницы: 36

Бренд: Quadra-Fire Страницы: 16

OUTLAND LIVING FM2BS-210

Бренд: FMI Страницы: 16

Бренд: Kuma Stoves Страницы: 12

Бренд: HASE Страницы: 16

Бренд: HAAS + SOHN Страницы: 20

Бренд: Costway Страницы: 11

Бренд: Dal Zotto Страницы: 176

Бренд: Dal Zotto Страницы: 164

Wood 3600 Range

Бренд: HWAM Страницы: 16

Бренд: Gasmate Страницы: 2

Ecofire Elisabeth Aria

Бренд: Palazzetti Страницы: 92

Бренд: Ashley Страницы: 28

Бренд: Waldbeck Страницы: 27

Бренд: WANDERS Страницы: 55

DISCOVERY I Series

Бренд: Quadra-Fire Страницы: 34

Бренд: Jide Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды