Leitronic AG EasyAlarm BASIC, Инструкция пользователя, Страница: 18 / 32

18
7.7 Phone connection
The colour of the indicator LED changes to orange during telephone connection.
7.7.1 Time-out
There is a timer running in the phone connection mode. Phone connection is kept up for two minutes in case of alarm call ,
and ten minutes in case of test call . Ten seconds before disconnection, the called person hears the announcement “abort”.
He/she can restart timer using DTMF 3 at any time.
7.7.2 Announcements
At the beginning of each phone connection the following information will be announced: Individual message followed by
the cause of alarm and the instruction to acknowledge alarm by pressing DMTF 0 . In a Listening-in connection you get
announcement: „to speak press 1“. This announcement is repeated every 8 seconds, until a tone-dialling command is
entered.
Notes:

At the beginning of any phone connection battery state will be checked and announced if low

At the beginning of any phone connection battery state and main voltage are checked. In case a test is negative an
appropriated message will be announced.

The numbers of unacknowledged alarms is announced.
7.7.3 Listening-in connection
Possible tone-dialling commands during the listening-in connection
DTMF => Every valid command will be signalled
0 Terminate phone connection and acknowledge alarm
1 Switching to hands-free mode and restart connection time-out
2 Repeat announcements ( Individual message / Cause of alarm)
3 Restart connection time-out (2 minutes)
4 Deactivate output (i.e. switching off alarm siren)
5 Announcement of current supervision mode as well as condition of the output
6 Activate output (i.e. switching on the alarm siren)
7 Change to inactive supervision mode (I, II, III) => monitoring for noise, sensor-1, sensor-2, mains failure and
presence verification inactive. Emergency call and sensor-3 alarm are still possible.
8 Terminate phone connection without acknowledgment
9 Change to active supervision mode (I, II, III) => All monitoring functions re-activated
* * 0 Announcement of calling number sequence
* * n Announcement of calling number n ( n = 1..9)
Following tone-dialling command can be used for remote programming, provided the programming is not blocked (

section 10.6)
* * #
Trigger an alarm for test reasons

Cause of alarm announcement "alarm due to programming"
* * < n> * followed by the new calling number announcement and change of calling number n
* * # # Record individual message => according to section 6.3.1.
7.7.3.1 Use of siren during listening in connection
The activation of a siren (

section 11.2) can be done either manually during a listening-in connection using DTMF 6 or 4
or automatically in accordance to the reason of the alarm (

programming section 10.5.2).
7.7.4 Hands-free connection
The commands during hands-free connection are identical to the commands by listening in connection, except DTMF 1 .
Important note:

Hands-free connection must be terminated using DTMF 0 or 8 . Otherwise a busy tone signal appears until
phone connection is terminated due to time-out.

By selecting hands-free connection an activated siren (optionally) is automatically deactivated. If requested, the
siren can be activated or deactivated by DTMF 6 or 4 .
7.7.4.1 Adjustment of hands-free volume
During hands-free connection you can increase volume by pressing local key # . or decrease by pressing locale key * . .
Level can be adjusted in fifteen steps (1dB each) and remains stored.
7.7.5 Acknowledge alarm / Terminate connection
A called party can choose between acknowledgment by pressing DTMF 0 or passing on alarm to next party in calling
number sequence by pressing DTMF 8 .
Important notes:

There is no alarm repetition, if an alarm is triggered by pressing any key of the alarm unit (test call).

An alarm can be confirmed and terminated by pressing key 0 . of the alarm unit or by pressing the wireless
emergency button for a second time.

If the alarm is programmed to a pager, the called person can confirm alarm during remote-access after
dialling-in.
7.8 Alarm repetition
If an alarm has not been acknowledged by passing all the calling numbers in the sequence, a number of alarm repetitions
can be programmed (

programming 10.2). Factory setting: two alarm repetitions.