Leitch DMX-3901-A Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 64

Leitch DMX-3901-A Скачать руководство пользователя страница 41

26

DMX-3901-A Installation and Operation Manual

Chapter 3: Operation

Alarms

DMX-3901-A modules provide a default list of five alarms. You can
disable any alarm by modifying the

Alarms

parameter in the

Setup

section.
When you select

Alarms

, all of the active alarms are visible in the

display, below

Config

(Configurations). If no alarms are active, only

Config

appears.

Alarm Synchronization

Alarm synchronization is available for this module if your NEO frame
contains a 3901RES-E resource module that supports the feature. When
active, alarm synchronization ensures that the alarm configuration
settings of card-edge controls and the CCS control software and control
panels are consistent.
If the DMX-3901-A module is set for local control, the alarm settings
will appear the same at both the card edge and via CCS, but the settings
can only be changed using the card-edge controls. If the module is set
for remote control, the alarm settings can be changed via both the
card edge and CCS control software and control panels.
Alarm configuration settings undergo DejaView (state recovery)
automatically. This means that when a module is hot-swapped, the
alarm configuration for the new module is updated to the settings of the
module that was previously in that slot. See “State Recovery Parameter
Availability” in this chapter for more information.

Identifying the Cause of an Alarm

To identify the reason for an alarm, select the active alarm, and then
press

Enter

. A scrolling message appears on the VFD describing the

cause of the fault.

«
...
39
40
41
42
43
...
»

Содержание DMX-3901-A

































































Отзывы:

Нет отзывов