manualshive.com logo in svg

Leitch DMX-3901-A, Инструкция по установке и эксплуатации, Страница: 24 / 64

Поделиться
Скачать
Leitch DMX-3901-A Скачать руководство пользователя страница 24

DMX-3901-A Installation and Operation Manual

9

 Chapter 2: Installation and Removal

  

Setting Jumpers

Four jumpers, labelled J22, J23, J24, and J25, are located at the right 
side at the back of the module. These jumpers determine the analog 
audio output level for output channels 1, 2, 3, and 4 respectively.
Each jumper set consists of three pins, with Pin 1 marked by a white 
triangle. When Pin 1 is covered by the jumper, the output is switched to 
28 dBu. When Pin 1 is not covered, the output is switched to 18 dBu. 

Figure 2-1

 shows the location of the jumpers on the module.

Figure 2-1. 

Location of Jumper Pins.

Figure 2-2

 illustrates the jumper selection for either 28 dBu or 18 dBu 

audio output setting.

Figure 2-2. 

Jumper Selection for 28 dBu or 18 dBu Settings

J25

J24

J22

J23

VFD display

Back of module

Note

The module calibration is 
performed with the jumper in 
the default setting of 28 dBu.

28 dBu

18 dBu

Pin 1 board marker

Third pin

uncapped

First pin

uncapped

Содержание DMX-3901-A

































































Отзывы:

Нет отзывов