background image

BD

A M610 LE

GIC L043-A03 2022-07-12 (GB)

16

REMOVE LEGIC MTSC CONFIGURATION ON RFID SYSTEM

With the SAM 64 (System Authorization Media) card, which is part of the LEGIC MTSC (Master-Token System-Control), 
the previously created authorizations and configurations by using the SAM 63 card are deleted again in the RFID reader. 
Following that, all types of transponders mentioned on page 2 under technical specifications can be used again. The lock 
must be open when using the SAM 64 card.

Remove configuration with LEGIC SAM 64 card

Master

       

Hold the master card  
in front of the reader.

    

        

  

    

  

SAM 64

Hold the LEGIC SAM 64  
card in front of the reader.

    

    

                    

    

             

             

                         

Master

Hold the master card  
in front of the reader.

    

  

    

             

BATTERY WARNING

The locking system is equipped with a battery management system which uses visual and acoustic signals to indicate 
the need for battery replacement in the event of reduced battery power. The battery warning takes place in two 
phases:

Battery warning Phase 1

Before an action can be carried out (closing / 
opening / programming), a battery warning is given. 
The batteries should be replaced.
The battery warning is also given every 60 minutes.

    

    

    

    

  

    

    

    

    

Battery warning Phase 2

The lock can only be opened. Before the lock opens, 
a battery warning is given. The batteries must be 
replaced without delay.
The battery warning is also given every 60 minutes.

    

    

    

    

    

  

    

    

    

    

    

Содержание M610 L043-A03





















Отзывы: