lehman Trikes DYNA Скачать руководство пользователя страница 27

Страница: 27 / 34

2006-2013 FXD Renegade Rev. 6

License Plate Light

See Fig. 5

. Install license plate bracket to door with 1/4” x

1” bolts, washers, lock nuts and rubber washers. Use

rubber washers between bracket and door. Install U-nuts

to bracket

(2) 1/4” x 1” Button head bolt (CB1086)

(2) 1/4” Rubber washer (FG1002)

(2) 1/4” Flat washer (CW2005)

(2) 1/4” Lock nut (CN3040)

(2) 1/4” U-nut (CN3301)

See Fig. 6.

Install license plate light and support plate to

bracket using (2) 1/4” x 1 bolts.

See Fig. 5

. Run wiring through lower hole in door.

(1) License plate light (S001469)

(1) Support plate (S001601)

(1) 1/4” x 1 Button head bolt (CB1086)

(2) M6 Flat washer- CW2175

See Fig. 6

. Install lower license plate mounting hardware

into place on support bracket using 1/4” x .50” bolts and (2)

lock nuts

(2) 1/4” x .50 Button head bolt (CS4032)

(2) 1/4” Lock nut (CN3040)

5. Solder and heat shrink light wiring to trunk wiring harness.

Attach wire as follows-

Black

wire on light to

Black

wire on trunk harness

Red

wire on light to

Red

wire on trunk harness

6. Seal wiring through door with silicone (Ultra Black).

Fig. 5

Fig. 6

Install rubber washers
between bracket and door

Install wire through lower hole

U-nut

Содержание DYNA



































Результаты поиска

Содержание DYNA

Отзывы:

Похожие инструкции для DYNA

Бренды по названию

Популярные бренды

lehman Trikes DYNA, Руководство по установке

Результаты поиска

Содержание DYNA

Отзывы:

Похожие инструкции для DYNA

Бренды по названию

Популярные бренды