lehman Trikes DYNA Скачать руководство пользователя

Страница: 8 / 34

2006-2013 FXD Renegade Rev. 6

06-07 Models

See Fig. 3

. Install swingarm pin brace

(LB6110) to RH side of transmission housing with

original hardware from case. Leave bolts for this bracket

loose until swingarm installation is complete.

08-13 Models:

See Fig. 4

. Install swingarm pin brace

(LB6110) to RH side of transmission housing with

original hardware from case. Install (S001057- Fig. 4)

spacer between case and pin brace. Leave bolts for this

bracket loose until swingarm installation is complete.

All Models

8. Install Lehman swingarm with word “TOP” (stamped into

swingarm collar) facing upward.

See Fig. 4

.Place swingarm pivot bolt spacer

(LS6129) on RH side of swingarm between swingarm

bearing and LB6110 bracket.

10. On pivot bolt (LP6105) install a new (CW2032)

washer against bolt head.

11. Holding swingarm in place, insert pivot bolt assembly

through RH side and into swingarm and transmission

case. Start stock flange nut as bolt emerges from

bearing on LH side. Use Loctite 242 on threads.

Torque to

150 ft. lbs

Note: Make sure bolt end does not contact primary

case.

12.

See Fig. 3.

Using Loctite 242 tighten all fasteners for LB6110 swingarm pin bracket. Torque to

20 ft.

lbs

13. Be sure swingarm moves freely up and down with no side to side movement.

Fig. 3 LB6110 Pin Brace, 06-07 Models

S001057 Spacer-
2008+ Models

LS6129

CW2032

Fig. 3

Fig. 4

Содержание DYNA



































Результаты поиска

Содержание DYNA

Отзывы:

Похожие инструкции для DYNA

Бренды по названию

Популярные бренды

lehman Trikes DYNA, Руководство по установке

Результаты поиска

Содержание DYNA

Отзывы:

Похожие инструкции для DYNA

Бренды по названию

Популярные бренды