Leguan L190 Скачать руководство пользователя страница 48

Страница: 48 / 53

_________________________________________________________________________________

11. INSTRUCTIONS

FOR

TEMPORARY

STORAGE

The cable of the

pole of the battery should be disconnected, if the access platform is being

stored for a period longer that one month.

The access platform shall be covered and, if possible, stored inside or under a roof in a
place where unauthor

ized persons don’t have access.

Make sure possible leaks during storage will not cause waste water or similar environmental
issues.

After long storage period perform necessary checks and maintenance routines according to
the service schedule.

ATTENTION!

See also engine manufacturer’s instructions for the storage of the

engine.

12. INSTRUCTIONS

FOR

DISPOSING

THE

ACCESS

PLATFORM

When the access platforms lifecycle comes to an end, it has to be dissembled and disposed of in an
environmentally friendly way.

Battery and other electronic components should be recycled or disposed of according to local
regulations.

Oil should be collected and recycled according to local regulations.

Plastic parts should be recycled according to local regulations.

Metal parts should be recycled according to local regulations.

Содержание L190






















































Результаты поиска

Содержание L190

Отзывы:

Похожие инструкции для L190

Бренды по названию

Популярные бренды

Leguan L190, Руководство оператора и по обслуживанию

Результаты поиска

Содержание L190

Отзывы:

Похожие инструкции для L190

Бренды по названию

Популярные бренды