Leguan L190 Скачать руководство пользователя страница 31

Страница: 31 / 53

_________________________________________________________________________________

8. SERVICE,

MAINTENANCE

AND

INSPECTION

REGULATIONS

This access platform must be inspected once a year. The inspection can only be done by a
qualified person.

Persons who conduct the periodical services shall familiarize themselves with the

operation and technical features of this access platform before doing any service operations. All
service and maintenance operations must be made in accordance with the instructions in this manual.

8.1 General instructions

It is not allowed to make any changes on the construction of the machine without written
permission from the manufacturer.

All defects that may have an effect on the safe use of this access platform must be repaired
before starting operation.

Only professional persons are allowed to open the covers and handle the electric etc.
components. Risk of serious injury!

Make sure that services are made in accordance with this Operators Manual and with the
Service Manual of the engine manufacturer.

Stop the engine before starting any service or inspection operation, DISCONNECT ALSO THE
230 V MAINS CURRENT.

Do not smoke during service and inspection operations.

Keep the machine and especially the platform clean.

Make sure that the operating instructions are complete, readable and in their place in the box
at the platform.

Make sure that all stickers are in their place and readable.

Make sure that the access platform has been serviced according to the manual.

Make sure that all inspections have been made according to local regulations.

ATTENTION! All spare parts

– especially electric components and sensors – must be

original Leguan parts.

Содержание L190






















































Результаты поиска

Содержание L190

Отзывы:

Похожие инструкции для L190

Бренды по названию

Популярные бренды

Leguan L190, Руководство оператора и по обслуживанию

Результаты поиска

Содержание L190

Отзывы:

Похожие инструкции для L190

Бренды по названию

Популярные бренды