LEGRAND vaddio 999-99800-100 Скачать руководство пользователя страница 66

Страница: 66 / 95

network settings get

Returns the current network settings for MAC address, IP address, subnet mask, and gateway.

Synopsis

network settings get

Example

network settings get

Name

eth0:WAN

MAC Address

48:6F:77:64:79:21

IP Address

192.168.1.67

Netmask

255.255.255.0

VLAN

Disabled

Gateway

192.168.1.254

streaming settings get

Retrieves IP streaming settings. These are configured in the web interface.

Synopsis

streaming settings get

Parameters

IP Custom_Frame_Rate

Frame rate (Custom mode).

IP Custom_Resolution

Resolution (Custom mode).

IP Enabled

True

if IP streaming is enabled,

False

if it is

not.

IP MTU

Maximum packet size.

IP Port

Port number used for IP streaming. Default for
RTSP streaming is 554; default for RTMP
streaming is 1935.

IP Preset_Quality

Video quality (Easy mode).

IP Preset_Resolution

Resolution (Easy mode).

IP Protocol

IP streaming protocol in use (RTSP or RTMP).

IP URL

URL where the RTSP stream is available.

IP Video_Mode

Video quality mode selected (preset or custom)

Example

Returns the current streaming settings.

Complete Manual for the RoboFLIP 30 HDBT In-Ceiling HD PTZ Camera

Содержание vaddio 999-99800-100
































































































Результаты поиска

Содержание vaddio 999-99800-100

Отзывы:

Бренды по названию

Популярные бренды

LEGRAND vaddio 999-99800-100, Полное руководство

Результаты поиска

Содержание vaddio 999-99800-100

Отзывы:

Бренды по названию

Популярные бренды