LEGRAND vaddio 999-99800-100 Скачать руководство пользователя страница 29

Страница: 29 / 95

Stopping the IP Stream

TREAMING PAGE

Options:

To stop IP streaming entirely:

Clear the Enable IP Streaming check box.

To stop the video portion of the stream, but leave the stream running:

Mute the video. This also

stops the video locally, so the connected display is blank.

To stop sending the stream to a content service provider but make it available as a network
stream:

Change from RTMP to RTSP streaming.

Setting up RTSP Streaming in Easy Mode

TREAMING PAGE

If you are not sure how to configure streaming settings, start with the Easy mode defaults. This configures
most settings automatically.

1. Select Easy quality mode.

2. Select the desired IP streaming resolution. This determines the size of the window in which the stream

is displayed.

3. Select Video Quality.

4. Save your changes.

Pro Tip

If streaming video quality is poor, try a lower resolution or bandwidth.

Complete Manual for the RoboFLIP 30 HDBT In-Ceiling HD PTZ Camera

Содержание vaddio 999-99800-100
































































































Результаты поиска

Содержание vaddio 999-99800-100

Отзывы:

Бренды по названию

Популярные бренды

LEGRAND vaddio 999-99800-100, Полное руководство

Результаты поиска

Содержание vaddio 999-99800-100

Отзывы:

Бренды по названию

Популярные бренды