LEGRAND vaddio 999-99800-100 Скачать руководство пользователя страница 46

Страница: 46 / 95

Installing a Camera Firmware Update

YSTEM PAGE

, F

IRMWARE TAB

Caution

The camera must remain connected to power and to the network during the update. Interrupting the update
could make the camera unusable.

1. Download the firmware and its release notes.

2. Select Choose File, then browse to the downloaded firmware and select it. The filename ends with

.p7m

3. Select Begin Firmware Update.

4. Read and understand the information in the Confirm dialog box. It's dull, but it could save you some

time and aggravation.

5. Select Continue. A progress message box opens and the status light on the front of the camera turns

yellow. If the update process presents warnings or error messages, read them carefully.

The camera reboots when the update is complete.

Complete Manual for the RoboFLIP 30 HDBT In-Ceiling HD PTZ Camera

Содержание vaddio 999-99800-100
































































































Результаты поиска

Содержание vaddio 999-99800-100

Отзывы:

Бренды по названию

Популярные бренды

LEGRAND vaddio 999-99800-100, Полное руководство

Результаты поиска

Содержание vaddio 999-99800-100

Отзывы:

Бренды по названию

Популярные бренды