LEGRAND STARK 10 kVA Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 52

LEGRAND STARK 10 kVA Скачать руководство пользователя страница 20

20

4.2.1 Restart procedure

4.2 TURN ON/OFF UPS

If the Rectifier input is within voltage
range, the rectifier will start up in 30
seconds then the inverter will start up
after then.

If the rectifier fails at startup, the bypass LED
will light up. When the inverter starts up, the
UPS will transfer from bypass mode to inverter
mode, and then the bypass LED extinguishes
and the inverter LED lights up.

No matter whether the UPS can work normally
or not, all the status will be shown on the LCD
display.

CAUTION:

Make sure grounding is properly done!

WARNING:

Check to see if the load is safely connected with the output of the

UPS. If the load is not ready to receive power from the UPS, make

sure that it is safely isolated from the UPS output terminals

ώ

Set the Battery Breaker to the “ON” for long run UPS.

ώ

Switch ON the power switch for standard UPS.

ώ

Switch ON UPS input switch

ώ

Switch ON UPS output switch

O/P switch

I/P switch

POWER

«
...
18
19
20
21
22
...
»

Содержание STARK 10 kVA





















































Отзывы:

Нет отзывов