Leadvision Pool Fence, Руководство по установке

Страница: 11 / 13

11
Your cut has been made and you now have to attach the border material included. Place mesh between both
flaps of the border and slide the strip of border down the mesh then staple it on. Staples should be 1/4’’ off line of
mesh in border. See
Fig. 27-28 . Make sure the mesh fully inserted in side the border material included.
Now your border has been attached to the cut side of the mesh. Cut of excess border. Your next step is to attach
the pole you removed in
Fig. 26 to the cut side. The best way to attach your pole to the cut is as follow:
• Lay your molding strip on top of the border you just attached.
Fig. 29
• Line up molding so that it’s flush with bottom & flush with line of mesh. Make sure all staples are covered by
molding Fig. 29
• Screw one screw into the molding at the top until it comes completely through the molding mesh and border
• Then put one screw into the molding at the bottom until it comes through to the side of the molding and mesh.
Your molding should now be attached with 2 screws to the cut piece if the fence.
• Slide your pole underneath the molding & mesh, and align the screws that came through the otherside to the
corresponding holes of the pole. Partially back out your top screw while keeping pressure on the molding and
the pole to keep it from moving. Then slowly drive the screw back down into the pole. Repeat this step for the
bottom screw . See
Fig. 30
• Finally place the rest of the screw into the pole and slowly screw them down. Your end pole is now attached.
Your cut has been made and you now have to attach the border material included.
Place mesh between both flaps of the border and slide the strip of border down the
mesh then staple it on. Staples should be 1/4’’ off line of mesh in border. See
Fig.27-28 . Make sure the mesh fully inserted in side the border material included.
Now your border has been attached to the cut side of the mesh. Cut of excess border.
Your next step is to attach the pole you removed in Fig.26 to the cut side.
The best way to attach your pole to the cut is as follow:
*lay your molding strip on top of the border you just attached.
Fig.29
*Line up molding so that it’s flush with bottom & flush with line of mesh. Make sure
all staples are covered by molding Fig.29
*Screw one screw into the molding at the top until it comes completely through the
molding mesh and border
*Then put one screw into the molding at the bottom until it comes through to the side
of the molding and mesh. Your molding should now be attached with 2 screws to the
cut piece if the fence.
*Slide your pole underneath the molding & mesh, and align the screws that came
through the otherside to the corresponding holes of the pole. Partially back out your
top screw while keeping pressure on the molding and the pole to keep it from
moving. Then slowly drive the screw back down into the pole. Repeat this step for
the bottom screw . See Fig.30
*Finally place the rest of the screw into the pole and slowly screw them down. Your
end pole is now attached.
Fig. 27
1/4” off line of mesh
Staples should be 1/4” off edge
where border meets mesh
Your cut has been made and you now have to attach the border material included.
Place mesh between both flaps of the border and slide the strip of border down the
mesh then staple it on. Staples should be 1/4’’ off line of mesh in border. See
Fig.27-28 . Make sure the mesh fully inserted in side the border material included.
Now your border has been attached to the cut side of the mesh. Cut of excess border.
Your next step is to attach the pole you removed in Fig.26 to the cut side.
The best way to attach your pole to the cut is as follow:
*lay your molding strip on top of the border you just attached.
Fig.29
*Line up molding so that it’s flush with bottom & flush with line of mesh. Make sure
all staples are covered by molding Fig.29
*Screw one screw into the molding at the top until it comes completely through the
molding mesh and border
*Then put one screw into the molding at the bottom until it comes through to the side
of the molding and mesh. Your molding should now be attached with 2 screws to the
cut piece if the fence.
*Slide your pole underneath the molding & mesh, and align the screws that came
through the otherside to the corresponding holes of the pole. Partially back out your
top screw while keeping pressure on the molding and the pole to keep it from
moving. Then slowly drive the screw back down into the pole. Repeat this step for
the bottom screw . See Fig.30
*Finally place the rest of the screw into the pole and slowly screw them down. Your
end pole is now attached.
Fig. 29
Fig. 30
Place one screw
at top
Molding is flush
with mesh
Mesh over hangs
on outside of
molding covering
all staples
Partially Back out
screw then screw it
back in
Partially Back out
screw then screw it
back in
Place one screw
at bottom