manualshive.com logo in svg

Leadshine MX3660, Руководство по установке оборудования

Поделиться
Скачать
Leadshine MX3660 Скачать руководство пользователя страница 11

                         

                         

Hardware

 

installation manual of the multi-axis drive MX3660

 

Leadshine Technology Co., Ltd   

 

 

 

 

 

 

 

Leadshine America, Inc. 

 

 

 

 

       

Page 11/25

 

11/F, Block A3, iPark,

 

No.1001 Xueyuan Blvd, Nanshan District, Shenzhen, China 

25 Mauchly, Suite 318, Irvine, CA 92618, USA    

Tel:

 86-755-26409254 

 

Fax: 86-755-26402718 

 

 

 

 

Tel: 1-949-608-7270   

 

Fax: 1-949-608-7298 

Web

:

 

www.leadshine.com

 

Email:

 

[email protected]

 

           

 

Web:

 

www.leadshine.com

 

Email:

 

[email protected]

   

10.

 

  Enabling / Disabling Charge Pump 

To  make  the  MX3660  working  properly,  setting  this  switch  to  the  right  position  is  required.

  The  MX3660  is 

featured  with  a  feature  called  “Charge  Pump”,  a  watchdog  timer  to  enable/disable  the  MX3660.  When  the 
charge pump feature is turned on, the MX3660’s activation will depend on the receiving of 10 kHz signals at pin 
16 of the DB25 connector. When the “Charge Pump” feature is turned off, the MX3660 will be activated without 
such verification. 

By default, the charge pump feature is turned on, with the “Pulse Switch” (next to the DB25 connector) set to 
the  “Off”  position  (means  “Charge  Pump”  on).  To  disable  this  feature  and  make  the  MX3660  to  work  with 
control  systems  (e.g.  PLC,  motion  controller,  etc.)  not  designed  to  use  the  “Charge  Pump”  feature,  set  the 
“Pulse Switch” to “ON” position (meaning “Charge Pump” off).

 

 

Figure 11  On/Off positions for “Pulse Switch” and “Smoother” Switches 

!

Caution

 

The ON/OFF direction for the “Pulse Switch” is different from the ON/Off direction 
of the DIP switch in a stepper drive module, which is used to configure the output 
current and micro step by a stepper drive module. Refer to Figure 11.

   

 

11.

 

Setting the “Smoother” Switch 

The firmware of each of the three stepper drive modules in the MX3660 adopts a feature called 
“smoothing”  to  smooth  input  step  signals. 

When  an  input  pulse  emulated  by  the  connected  motion 

controller or CNC control system are not in linear or equivalent width, called “noise pulse”, it will cause erratic 
motion and additional motor/drive noise. Turning on the built-in digital smoother will trigger the input pulse 
train smoothing and could potentially improve motion performance such as less jittering, higher torque, and 
quicker response. Because of the complexity for different machines/devices, the “Smoother” feature may or 
may not have obvious effect (but at least no hurt for the bottom line). Turning on this switch or off is totally 
your choice. 

The “Smoother” switch is located next to the DB25 connector. By default, the MX3660 smoother is set to off. 

!

Caution

 

The  ON/OFF  direction  for  the  “Smoother”  switch  is  different  from  the  ON/OFF 
direction of the three DIP switches for the 3 stepper drive modules, which is used to 
configure output current and micro step by a stepper drive module. Refer to  Figure 
11 for “Smoother” switch direction.

 

Содержание MX3660


























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды