LBS LBS-12150-HP-REG Скачать руководство пользователя страница 26

Страница: 26 / 28

MED HP Batteries

–

Installation & User Guide

Installation & User Guide

HP Batteries; Medium Size

The TERM CUR value indicates the amount of current into or out of the gray Anderson connector

and the battery terminals, which are both connected in parallel. Low readings of ±0.3 Amps can be

taken as a zero-value due to the response of the electronics to small changes in measurement.

For example, if you had a solar panel connected to the black Anderson connector, the diagnostic

screen will show the input current for BIC1-MON:

A solar panel could also be connected to the red Anderson connector which corresponds to BIC2-

PVC, or it could be connected to the blue Anderson connector which corresponds to BIC3-DCS.

Содержание LBS-12150-HP-REG





























Результаты поиска

Содержание LBS-12150-HP-REG

Отзывы:

Похожие инструкции для LBS-12150-HP-REG

Бренды по названию

Популярные бренды

LBS LBS-12150-HP-REG, Инструкция по установке и эксплуатации

Результаты поиска

Содержание LBS-12150-HP-REG

Отзывы:

Похожие инструкции для LBS-12150-HP-REG

Бренды по названию

Популярные бренды