manualshive.com logo in svg

LawnMaster NPTBSP2609A, Руководство по обслуживанию, Страница: 5 / 42

Поделиться
Скачать
LawnMaster NPTBSP2609A Скачать руководство пользователя страница 5

5

SPECIFICATIONS

Flywheel cover to 

crankcase

Apply a thermostable screw-thread glue into the two 

holes on crankcase. Tighten the 2 screws (M5X15) 

securing the flywheel cover to crankcase.

53-64

6-7.2

Lower engine cover 

assembly

Place the lower engine cover onto crankcase. Tighten 

the 3 screws (1*ST3.9X8, 2*M5X10) securing the 

lower engine cover.

10-12

1.1-1.3 (for 

1*ST3.9X8)

27-35

3-4 (for 

2*M5X10)

Upper engine cover 

assembly

Tighten the 3 screws (M5X35) securing the upper 

engine cover.

27-35

3-4

Spark plug cover to 

upper engine cover

Tighten the screw (M5X10) securing the spark plug 

cover to upper engine cover.

27-35

3-4

Lower engine cover to 

upper engine cover

Tighten the screw (ST3.9X12) to secure the upper and 

lower engine covers (on muffler side).

10-12

1.1-1.3

Right handle cover to 

left handle cover

Tighten the screws (ST3.9X16) to secure the right and 

left parts of the main handle.

10-12

1.1-1.3

Transmission yoke to 

flywheel cover

Apply a thermostable screw-thread glue into the four 

screw holes on flywheel cover. Tighten the screws 

(M5X20) securing the transmission yoke.

53-62

6-7

Shaft connection sleeve 

to upper shaft

Align the shaft connection sleeve with the screw holes 

on upper shaft. Tighten the screws (M5X25 & M5X12) 

securing the shaft connection sleeve to upper shaft.

53-62

6-7

Gear box to lower shaft

Align the screw holes on the gear box with the lower 

shaft. Tighten the screws (M5X12, M6X25, M6X10) 

securing the gear box to lower shaft.

53-62

6-7

Transmission yoke 

assembly

Align the screw holes on the transmission yoke with 

the screw holes on upper shaft. Tighten the screws 

(M5X12 & M6X25) securing the transmission yoke to 

upper shaft.

53-62

6-7

Shoulder strap clasp 

assembly

Adjust the position of the shoulder strap clasp and 

tighten the screw (M5X16).

27-35

3-4

Trimming line cutting 

blade assembly

Tighten the screws (ST3.9X16) with washers to secure 

the trimming line cutting blade to the debris guard.

10-12

1.1-1.3

Ratchet to electric 

starter assembly

Attach the ratchet to the electric starter lower cover. 

Apply a thermostable screw-thread glue onto the head 

section of the screw (M5X10) and tighten the screw 

(M5X10) securing the ratchet.

27-35

3-4

Electric starter motor 

assembly

Align the electric starter motor with the screw holes on 

the electric starter upper cover. Apply a thermostable 

screw-thread glue onto the head section of the screws 

(M3X8) and tighten the screw securing the electric 

motor.

4-6

0.5-0.7

Electric starter lower 

and upper covers 

assembly

Tighten the two screws (ST2.9X12F) securing the 

lower and upper covers of the electric starter.

4-5

0.4-0.6

Содержание NPTBSP2609A











































Отзывы:

Нет отзывов