manualshive.com logo in svg

LawnMaster NPTBSP2609A, Руководство по обслуживанию, Страница: 3 / 42

Поделиться
Скачать
LawnMaster NPTBSP2609A Скачать руководство пользователя страница 3

3

SPECIFICATIONS

TORQUE SPECIFICATIONS

Engine Size                                                                              2-Stroke / Full Crank
Engine Displacement Claimed / Rated                                                                            26cc / 25.4cm

3

Ignition                                                                Capacitor Discharge Ignition (CDI)

Carburetor                                        All Position Diaphragm Type With Primer Bulb
Air Filter                                                                                                   Foam (Dry)
Engine Shut Off                                                                                       Auto-Reset
Throttle Control                                                                     Variable Speed Trigger
Fuel / Oil Ratio                                                                                                 40 : 1
Fuel Tank Capacity                                                                                         400 ml

Spark Plug                                                                                    Champion RCJ6Y
Rotor Air Gap                                                             0.012”-0.015” (0.30-0.40 mm)
Spark Plug Gap                                                                             0.026” (0.65 mm)
Run Time on Full Tank                                                                                    30 Minutes

UNIT SPECIFICATIONS

Engine

Fuel System

General

Application

Description

Torque

Torque

(IN.LBS)

(N.m)

Crankcase

Apply a thermostable screw-thread glue onto the 4 

screws (M5X30) and then fix the crankcase cover.

53-62

6-7

Cylinder to crankcase

Apply a thermostable screw-thread glue onto the 4 

screws (M5X20) and then tighten the screws securing 

the cylinder to crankcase.

53-62

6-7

Spark plug to cylinder Pre-screw the spark plug to the cylinder, and then 

tighten with a torque spanner.

115-137

13-15.5

Carburetor mount to 

cylinder

Apply a thermostable screw-thread glue onto the 2 

screws (M5X20) and tighten the screws securing the 

carburetor mount to the cylinder.

35-44

4-5

Содержание NPTBSP2609A











































Отзывы:

Нет отзывов