manualshive.com logo in svg

LawnMaster NPTBSP2609A, Руководство по обслуживанию, Страница: 4 / 42

Поделиться
Скачать
LawnMaster NPTBSP2609A Скачать руководство пользователя страница 4

4

SPECIFICATIONS

Flywheel to crankshaft

Apply a thermostable screw-thread glue onto the 

crankshaft thread. Pre-screw the flange hexagon nut 

(M8) and then tighten.

89-133

10-15

Clutch to flywheel

Slide the corrugated washers onto the clutch bolts 

(M6X21.5). Apply a thermostable screw-thread glue 

onto the bolt thread head section. Install the bolts into 

the clutch and tighten the bolts securing the clutch to 

flywheel.

71-89

8-10

Ignition coil to cylinder

Put the 2 screws (M5X20) through the ignition coil 

and two spacers respectively. Apply a thermostable 

screw-thread glue into the cylinder holes and then pre-

screw the 2 screws (M5X20). Insert a feeler gauge 

of 0.014 in. (0.35mm) between the flywheel and the 

ignition coil. Press down the ignition coil flush against 

the feeler gauge. Tighten the screws with a torque 

spanner securing the ignition coil. Remove the feeler 

gauge.

27-35

3-4

Muffler to crankcase

Put the 2 bolts (M5X50) through the muffler assembly. 

Apply a thermostable screw-thread glue onto the 2 

bolts and secure the muffler to the crankcase using 

the torque wrench.

62-71

7-8

Apply a thermostable screw-thread glue onto the 

head section of 1 screw (M5X10). Pass the screw 

through the positioning hole on the muffler assembly 

holder and tighten the screw securing the muffler to 

crankcase.

62-71

7-8

Pawl assembly to 

crankshaft

Apply a thermostable screw-thread glue onto the 

crankshaft thread. Pre-screw the pawl assembly to 

crankshaft, and then tighten using the torque wrench.

62-80

7-9

Air filter base to 

carburetor

Pre-screw the nuts (M5) with washers, and then 

tighten using the pneumatic tool.

27-35

3-4

Fuel tank bracket to 

crankcase

Apply a thermostable screw-thread glue onto the 

screw (M5X10) and pass it through the hole on fuel 

tank bracket. Tighten the screw securing the fuel tank 

bracket to crankcase.

27-35

3-4

Fuel tank to crankcase

Apply a thermostable screw-thread glue onto the 

screw (M5X12). Pass it through the fuel tank hole. 

Tighten the screw securing the fuel tank to crankcase.

27-35

3-4

Cylinder pressure plate

Apply a thermostable screw-thread glue onto the 

screw (M5X10). Pass the screw through the cylinder 

pressure plate hole and then tighten it onto the 

cylinder.

27-35

3-4

Electric starter 

assembly to crankcase

Align the 2 screw holes on the electric starter 

assembly with the screw holes on crankcase. Tighten 

the 2 screws (M5X60) securing the electric starter 

assembly to crankcase.

27-35

3-4

Rear engine cover 

assembly

Tighten the 2 screws (ST3.9X30F) to secure the rear 

engine cover.

12-13

1.3-1.5

Содержание NPTBSP2609A











































Отзывы:

Нет отзывов