LawnMaster NPTBSP2609A Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 42

LawnMaster NPTBSP2609A Скачать руководство пользователя страница 16

16

GENERAL TROUBLESHOOTING

No load speed is not

stable/consistent.

Incorrect carburetor

adjustment.

Re-adjust the carburetor.

The carburetor has an air

leakage.

Replace or re-tighten.

Fuel tube is broken.

Replace.

Crankcase washer has air

leakage.

Replace.

Fuel seal has air leakage.

Replace.

After release the throttle

lever, the brush cutter

blade remains rotating.

Idle speed is too high.

Adjust the engine.

Clutch spring is broken.

Replace.

Clutch friction plate is

broken.

Replace.

The engine accelerates,

but the brush cutter blade

does not rotate.

Spline of the axle of

rotation or the spline of the

transmission yoke is worn

out.

Replace.

Irregular vibration.

Brush cutter blade is not

installed tightly.

Secure the brush cutter blade into place.

Brush cutter blade is bent.

Repair or replace.

Brush cutter blade is worn

out.

Replace.

The drive shaft is bent.

Replace.

Worn bearings.

Replace.

Clutch is off center.

Replace.

«
...
14
15
16
17
18
...
»

Содержание NPTBSP2609A











































Отзывы:

Нет отзывов