![background image](http://html1.mh-extra.com/html/launch/x-712/x-712_user-manual_4577788036.webp)
LAUNCH X-712 Wheel Aligner Maintenance
6-1
Maintenance
To prolong the service life of the equipment, the user
should maintain it with care. The X-712 wheel aligner is
of precision equipment which requires periodical
maintenance.
Computer
z
User should have a basic knowledge about
computer software and hardware to insure the
normal operation of the computer.
z
The computer host and the monitor should be
firmly secured on the right positions. Do not put
them in a freezing, wet, extremely hot or direct
sunlight place, or near the source of radiation and
heat.
z
Don’t foist anything into the computer host and the
monitor through the gap.
z
Do not switch on/off the computer too frequently.
z
Don’t change the BIOS setting at will.
z
Don’t delete the unknown files in the hard disc at
will to avoid abnormal computer operation or
death.
z
The computer is used only for X712 Wheel Aligner;
don’t install other software to the Wheel Aligner
computer to avoid computer virus. The computer is
scanned to ensure it is free of virus before leaving
factory.
z
Don’t use other software to avoid possible virus.
LAUNCH warranty does not cover the system
problem arising from the virus.
z
After a long period of use, the dust and oil dirt will
be accumulated on the computer host and the
monitor. Please cleanout it with neutral detergent
or dehydrated alcohol. Avoid using oil or caustic
product.
z
Never disassemble the computer and move the
inside cables and cards to avoid damage of the
inside components.
Wheel Clamp and Target
z
The wheel clamp should be cleaned and lubricated
timely to insure that the span of claws can be
easily adjusted and attached.
z
The targets of X-712 wheel aligner are the key
components for the alignment measurement, do
not damage their structures when using and
storing, keep the surface of target clean. Please
use the soft cloth dipped with an appropriate
amount of the neutral detergent or the absolute
alcohol to wipe the surface of target lightly if there
are some smuts on it.
z
Don’t disassemble the targets and clamps to avoid
damage of their elements. LAUNCH will not
guarantee for this kind of failure.
Printer
z
Read the operation instruction of the printer
carefully.
z
Install suitable printer drive program, and apply
right printer setting.
z
If the printed words are not clear, it may be that the
ink is used out. Please replace the printer ink
cartridge in time to resume the printing quality.
z
For other printer related problems, please contact
the customer service center.
Post, Lateral beam and Signal
Cables
z
There are two precision CCD cameras inside the
lateral beam. The precision position calibration has
been performed for the cameras after first
installation. The user can not move or wobble the
beam equipped with the cameras no matter during
or after using it.
z
Since computer visual technology is used to
recognize the targets mounted on the wheels
through the camera with high resolution, it is
necessary for X-712 wheel aligner to prevent the
outside infrared rays (e.g. sun-lights) from directly
lighting to the targets and reflecting to the cameras,
and it is necessary to avoid blocking the light way
from the targets and the cameras for a long time
during the instrument is working.
z
The wires inside the post and the lateral beam
equipped with the cameras are connected
compactly. Don’t move them after first installation.
z
Without approval of the supplier, please do not
disassemble the computer host and the lateral
beam equipped with the cameras in order to avoid
damaging the components, influencing the test
accuracy and increasing the costs and difficulties
of maintenance and repair. For the damage
caused by unauthorized disassembling will not be
covered by the Warranty.
Turntables
The mechanical turntables are precision components.
Avoid hitting during operation and never splash water on
them.
When moving the vehicle on the turntable, please insert
the locking pin to avoid the turntable sliding.
Generally speaking, it is not necessary to lubricate the
turntables frequently.
Содержание X-712
Страница 1: ...V2 01 000 2012 09 10 For X 712 X 712 Short Column X 712 Wall mounted X 712HD...
Страница 13: ...LAUNCH X 712 Wheel Aligner Structures 2 2 Fig 2 1 b X 712 Short Column Wheel Aligner...
Страница 14: ...LAUNCH X 712 Wheel Aligner Structures 2 3 Fig 2 1 c X 712 Wall mounted Wheel Aligner...
Страница 15: ...LAUNCH X 712 Wheel Aligner Structures 2 4 Fig 2 1 d X 712HD Wheel Aligner...