Manual: CS-8000RGB FX MK2 | CS-12.000RGB FX MK2
Manual: CS-8000RGB FX MK2 | CS-12.000RGB FX MK2
page 8 / 37
page 9 / 37
English
English
6. General Operation
1. Power
Connect the power cord to the device and to the mains. Make sure that your device is pro-
vided with the correct voltage. Wrong voltage could lead to irreparable damages. Please
find the correct voltage data in the synoptical table at the end of this manual. Make sure
that the device is not directed to people or inflammable objects during installation. To
start the device, connect the interlock bridge, insert the key and switch it on, and switch
the device on. The “Emission - Laser on“ LED at the front side of the device begins to
light up when the device is ready for use.
2. Key Switch
There is a key switch at the back of the laser system. Please plug the key to the switch and
turn it on. The laser device only runs when the key is inserted and switched on. Prevent
misuse! Unplug the key when the laser is unattended to prevent misuse of the sys-
tem.
3. Fuse
There is a fuse at the back side of the device. If the fuse should blow, please exchange
it with a new one. If the problems recurs, please contact your dealer or the Laserworld
service department.
4. Modes / Functions
The different operation modes can be selected via the four buttons next to the „Set-
tings“ display.
„Enter“ confirms a selection or navigates to the selected menu item.
„Up“ / „Down“ allows for stepping through the current menu or to make a selection.
„Exit“ exits the current menu item and moves one level higher.
4.1. SOUND-TO-LIGHT
Sound-to-light operation allows to playback the integrated patterns to the beat of music or
any noises.
Select „SoUd“ by navigating with the „Up“ / „Down“ buttons and confirm with „Enter“:
Standard selection is „ALL“, which means that all patterns saved on the main board are played
back. You can decide to use only a certain part of the pattern set with a certain grating by
selecting ALL (for all the gratings), L001, L002, L003, L004, or no grating with L005:
To set the sensitivity of the internal microphone, refer to chapter „4.5. Settings“
4.2. STAND-ALONE / AUTO
Stand-alone or Auto operation allows to random playback the internal patterns.
They are played back according to the internal system settings.
Select „AUto“ by navigating with the „Up“ / „Down“ buttons and confirm with „Enter“:
Standard selection is „All“, which means that all patterns saved on the main board are played
back. You can decide to use only a certain part of the pattern set with a certain grating by
selecting ALL (for all the gratings), L001, L002, L003, L004, or no grating with L005:
4.3. MASTER-SLAVE
This laser is Master-Slave capable. This means that the Master laser system can hand on a con-
trol signal to one or more Slave lasers, so all do the same.
Master-Slave only works with lasers of the same product series of the same product genera-
tion.
A: Link lasers with DMX cable
To use Master-Slave operation, link the Master with the Slave lasers with DMX cables. Make
sure to use the „DMX out“ port on the Master and the „DMX in“ on the Slave lasers. If several
Slave lasers are used, link the first one to the Master laser and daisy-chain the control signal
from the first Slave laser to the second etc..
B: Activate Master Laser
The Master laser needs to be set as control source.
Select „SEt“ by navigating with the „Up“ / „Down“ buttons and confirm with „Enter“:
• Clean the exit window with glass cleaner
from time to time
• Removal of the warranty label as well
as damages to the device caused by
improper handling, neglect of the sa-
fety instructions and service notes will
void the warranty.
